Screenint CINE PRO Betriebsanleitung Seite 2

INSTALLATION MANUAL
ENGLISH
INTRODUCTION
Thank you for purchasing the motorized Cine Pro projection screen. This
screen is made entirely in Italy with first-class materials, including a high
quality projection surface to guarantee excellent performance for your
installation.
WARNINGS
Before installing the screen, please read the following instructions carefully.
We would recommend that these instructions are stored safely for future
reference.
When opening the packaging of the screen, please DO NOT USE CUTTERS
or OTHER SHARP TOOLS that can damage the screen inside. During
opening the packaging and during installation, it is reccomended to use work
gloves.
Depending on the screen weight, it has to be handled by at least two or
three persons taking care to the following ratio KG/PERSON: MALE 25 kg.
– FEMALE 15 kg.
The manufacturer does not take responsibility for any damage to property or
personal injury if the screen is used outside of recommended specifications
or in case of incorrect/poor quality installation.
CERTIFICATIONS
Motorized screens Cine Pro are CE CEI EN 55014-1, CEI EN 50082-1, CEI
EN 61000-3-2, CEI EN 61000-3-3, CEI EN 60335-1, CEI EN 61000-3-2A14,
CEI EN 60335-2-97 certified.
The surfaces for projection used on the products are cadmium-free and are
fire-proof certified as follows:
class B1 – WHITE, MICROHOLES
The motor has a quality certification issued by IMQ (Istituto Italiano Marchio
di Qualità). Steel-wire cable is certified UNI EN 12385.
WARRANTY
This projection screen is guaranteed 2 years from the purchase date for
manufacturing defects.
Responsibility is limited to repairing or substitution of the defected
components and without any other charge at our expense.
Warranty is officially voided if the screen has been dismantled or it is returned
with collision damage or defective due to incorrect installation. Repairs must
be carried out by an Approved Screen International Certified Engineer.
Warranty is officially voided if:
1) the motor is removed / dismantled;
2) the screen has been transit damaged;
3) the instructions regarding the electrical connections have not been
followed;
4) the products have to be installed following the electric regulations (CEI)
and the other local specific laws;
5) in the installation are used electric interfaces that does not allow the
correct time lapse between up and down operation (complete cut down of
electric power on both phases for half a second)
6) electrical accessories have been used that are incompatible with the
screen motor causing damage to its internal components;
7) the motor end stops have been modified without the authorisation of the
factory;
8) the sticker regarding the serial number of the product has been altered,
deleted, removed or is illegible.
DO NOT install this screen nearby or over heating or air conditioning systems,
because PVC is a plastic material which dilates and remains damaged if it is
subjected to heat and/or cool air.
DO NOT install this screen either facing direct sun light or blocking a window
as PVC could be damaged and make waves for the explanations given
above.
The PVC cloth is very sensitive to temperature range. We advise to mount
the screen in environments with an ambient temperature in the range of 18°-
25°C.
We advise you to wait 2 hours for the screen to acclimatise before using the
screen after delivery, especially if screen is brought into a warm environment
from cold.
In case the screen is new or it has been rolled up for long time, roll down the
screen and leave it open for ca. 24/48 hrs. with an ambient temperature in
the range of 18°-25° C in order to get a perfect flatness of the cloth
DO NOT WASH the projection surface with alcohol or solvent nor with
commercial cleaners. Every now and then dust the surface with a dry and
clean duster.
Please, be very careful because any kind of stain on projection surfaces is
inerasable.
The screen has to be used showing the total projection sizes indicated on
the packaging; therefore it is NOT allowed to adjust the end stops to restrict
the total drop or extend it. Restricting the total drop of the screen is likely to
cause your screen surface to lose its flatness.
When the screen is not completely rolled down (as by factory setting), flatness
of the cloth is NOT guaranteed and therefore not covered by warranty.
DO NOT HANG TO THE SCREEN and DO NOT HANG ANY OBJECT to it.
Please take care that children DO NOT PLAY with the screen as they can get
severely injured.
The manufacturer will not accept returns of screens for repair without
manufacturer's authorization (RMA number) and without a suitable packaging.
INSTALLATION INSTRUCTIONS
1. ASSEMBLY
The product has to be installed and used conform to the laws in force within
the country where the product is used.
First of all, installation of Cine Pro screens has to be carried out from qualified
personnel. Our screen is supplied with ceiling brackets (Fig. 1) suitable for
fixing it to the ceiling by wall plugs (not supplied) specific for the type of
material to drill. Prior installing the roller screen, ensure that the ceiling is
suitable for the loading induced by the weight of the screen. In order to make
installation easier, we provide also lifting rings which can be used to lift the
screen and position it to the ceiling. During installation, please take care to
use security belts in order to secure the screen structure.
WARNING: USE ALL THE FIXING BRACKETS PROVIDED WITH THE
SCREEN IN ORDER TO INSTALL IT. Do not use the lifting rings to fix the
screen to the ceiling. THE LEFT AND RIGHT MOUNTING BRACKETS HAVE
TO BE FIXED AT THE SAME DISTANCE FROM EACH END SIDE OF THE
CABINET. THE FIXING DISTANCE HAS TO BE MAXIMUM 50 CM. FROM
LEFT AND RIGHT SIDES OF THE CABINET.
At the end of the installation, please check that the motorized screen is
perfectly level.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS, WALL PLUGS AND
BRACKETS ARE IN GOOD CONDITIONS AND WELL TIGHTENED.
2. ELECTRIC CONNECTION
Connection of the power supply must be carried out by qualified personnel
only, using the scheme showed on Fig. 2. Pay attention to wires colour
and fix the switch near the screen because the scrolling up or down of the
projection surface should be visible to the operator!! Never connect more
than one screen motor to the same switcher. Use the supplied switcher only.
IN CASE OF MAINTENANCE, UNPLUG THE POWER SUPPLY.
In case the screen is controlled via relais, take care that the control system
is programmed so there is no tension on the relais for at least 1 sec. during
switching between rolling up and rolling down operations and viceversa.
3. ADJUSTMENT OF THE END OF THE STROKES
The screen is supplied with a motor that has automatic limit switches that
determine both the closed stop position (closed screen) and the bottom stop
position (open screen).
The limit switches have been already fixed in our factory. We advise you NOT
to MODIFY them because modifying the closed stop position can cause
severe damages to the mechanical structure; whereas modifying the bottom
stop position can cause the movement of the steel-wire rope out of the
cylindrical pulleys.
4. MAINTAINANCE
Every now and then, the user should verify the condition of the steel-wire
cables. The precautionary measures state that the cables have to be
substituted when their tensile strength has decreased of 20%. For example:
the cable has 114 wires, it is time to substitute it when in 5 cm. of cable you
can count 20 or more broken wires.
CAUTION: CHECK EVERY 6 MONTHS THAT SCREWS, WALL
PLUGS AND BRACKETS ARE IN GOOD CONDITIONS AND WELL
TIGHTENED.
IT IS FORBIDDEN TO STAY UNDER THE PROJECTION SCREEN.
IT IS FORBIDDEN TO USE THE PROJECTION SCREEN OUTDOOR.
ONCE PROJECTION IS FINISHED, ROLL UP THE SCREEN (keeping
the screen rolled down can cause deformations to the projection
surface).
CINE PRO