Clas Ohlson AX300 Bedienungsanleitung Seite 2

Note: If you want the time switch to switch on one day and switch
off another day, you need to use 2 programmes. In this example
the switch will switch on at 20.00 hrs Monday and switch off at
06.00 hrs Tuesday. If you want to programme the switch to switch
on at 20.00 hrs on Monday you can e.g. use PROG 1 ON and set
the time and date. Then advance to PROG 2 OFF without setting
any times for 1 OFF and 2 ON. In programme 2 OFF setup mode
you should enter Tuesday 06.00.
To deactivate a programme
1
Choose the desired programme using the arrows [ ← → ].
2
Push [ SET ].
3
3 Push [ ON/OFF ] to deactivate
the programme. A cross
shows that the programme
is deactivated.
2 4
4
Push [ SET ] 3 times to exit
the cancel mode.
To deactivate all programmes
1
Advance to CLOCK using the arrows [ ← → ].
2
Push [ SET ].
3 Push [ ON/OFF ] to deactivate all the programmes.
A cross indicates that the programmes are deactivated.
4
Push [ SET ] 4 times to exit the cancel mode (cancel all).
Repeat steps 1–4 if you change your mind and don't
want to cancel the programmes.
Countdown Timer
This countdown timer starts in either the ON or OFF mode
and counts down when activated. In the ON mode the timer
switch emits 230 V. In the OFF mode the timer switch does not
emit any voltage.
GREAT BRITAIN • customer service tel: 08545 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
Setting the countdown timer
Choose PROG CD using
1
the left arrow [ ← ].
2
Push [ SET ].
3 Choose ON or OFF using the
arrows [ ← → ].
2 4
• The ON countdown starts when you push [ CD ].
ON during the countdown and thereafter OFF.
• The OFF countdown starts when you push [ CD ].
OFF during the countdown and thereafter ON.
4
1 Push [ SET ].
5
Set the hour using the arrows [ ← → ].
6
Push [ SET ].
7
Set the minutes using the arrows [ ← → ].
8
Push [ SET ].
9
Set the seconds using the arrows [ ← → ].
10
Push [ SET ].
Stop the countdown by pushing [ CD ] or [ ON/OFF ].
Random function
Short random: Operates for 1–2 hours at a time.
Long random: Operates for 2–3 hours at a time.
Programmable random: Operates for 1–2 hours at a time.
Short random: choose CLOCK.
1
Long random: choose CD.
2
Push [ RANDOM ].
"RND" flashes for short random.
3
"L-RND" flashes for long random.
Programmable random function
1
Choose programme 20 using the arrows [ ← → ].
2
Push [ RANDOM ].
PROG
CD
3 Set the time within which you
wish the random function to
operate.
3 5 7 9
6 8 4
10
"RND" is shown on the display.
• The programmable random function is only possible on
programme 20.
• Turn the random function off using [ RANDOM ] or [ ON/OFF ].
Manual ON/OFF
Push [ ON/OFF ].
Troubleshooting
Problem
The LCD display has frozen
and the buttons don't
respond when you
push them.
The timer switch's settings
are lost when it is not
connected to the mains.
The timer switch does not
perform the programmed
ON/OFF operations.
The timer switch does not
perform the programmed
ON/OFF operations at
certain times.
3
Technical Specification
1
2
Programmes
Rated voltage
Max Load
Shortest operating time
4
3
1
2
Solution
Push [ RESET ] to reset the timer.
Change the batteries.
Make sure that the programmes
are not deactivated.
Activate the programmes.
Make sure that the random
function is not activated. Make
sure that no other programmes
or countdown functions are
activated at the same time.
20
230 V AC, 16 A
3680 W Resistive load
1 minute