LD Systems STINGER G3 TMB Bedienungsanleitung

USER´S MANUAL
STINGER G3 TMB
EASYMOUNT® BRACKET FOR STINGER® 12" AND 15"
SAFETY INFORMATION
1. Please read these instructions carefully before you start installation and assembly.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Be attentive when mounting the product and protect yourself from injury.
6. This product is intended for indoor use only. Using it outdoors could lead to product failure and personal injury.
7. Do not modify this equipment.
8. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
9. Plastic bags must be kept out of reach of children.
10. If you have any questions refering to this instruction or any warnings, please contact your local distributor.
MANUFACTURER'S WARRANTY & LIMITATION OF LIABILITY
You can find our current warranty conditions and limitation of liability at:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_LD_SYSTEMS.pdf
To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,
61267 Neu Anspach / Email Info@adamhall.com / 49 (0) 6081 / 9419-0
PROPER DISPOSAL OF THIS PRODUCT
(WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT)
(Valid in the European Union and other European countries with waste separation)
This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste
disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable
economic activity.
LDEBG3TMB (suitable for LDEB122G3, LDEB122AG3, LDEB152G3, LDEB152AG3)
ASSEMBLY OF THE MOUNTING BRACKET AND TRAVERSE CLAMP
1. Release the safety splint (A) from the two M8 screws (B, C) in the cylindrical pivot/tilt head (D) of the
mounting bracket.
2. Unscrew the two screws (B, C) from the pivot/tilt head (D), separate the two cylinder halves and remove
the cast piece (E).
3. Now use the parts included – the M10 screw (F), spring washer (G) and self-locking M10 nut (H) – to at-
tach the cast piece (E) firmly to the traverse clamp (I) using a 17 mm socket tool. To do so, place the traverse
clamp in the recess of the cast piece and the self-locking nut in the recess of the traverse clamp and then
insert the screw with the spring washer through the cast piece into the traverse clamp (see illustration).
4. Now place the cast piece with the traverse clamp into one half of the pivot/tilt head (D) and join the two
halves in such a way that the M8 screw (C) can be placed through the appropriate installation hole of the one
half, through the support rail (J) of the mounting bracket and through the installation hole of the cylindrical
pivot/tilt head. Place the previously removed washer on the screw and finger tighten the M8 nut. Secure the
nut using the previously released safety splint (A).
5. Put the M8 washer onto the M8 lever screw (B), taking care to ensure that the M8 nut is correctly placed
in the recess of the appropriate cylinder half of the pivot/tilt head. Insert the lever screw through the two
cylinder halves and tighten. Secure the screw using a previously released safety splint (A).
H
I
E
G
F
D
J
A
SPECIFICATIONS
Model name: LDEBG3TMB
Type: PA Loudspeaker Accessories
Part: Truss Mount Bracket
Suitable for: LDEB122G3, LDEB122AG3, LDEB152G3, LDEB152AG3
Material: Steel/Zinc
Surface: Powder Coated
For further instructions, please check out the detailed online manual in the download area of this product at:: www.ld-systems.com
PARTS DESCRIPTION AND INSTALLATION
1. Traverse clamp for mounting on a horizontal traverse.
2. Wing nut for clamping to a traverse.
3. T-screw to lock the horizontal and vertical axes
4. Mounting rail with slots to adjust the vertical dispersion of the speaker.
5. Retaining pin.
6. Rotation mechanism for adjusting the horizontal dispersion of the speaker.
7. Three steel hooks which insert into the retaining sockets on the top of the speaker.
8. Two spring-loaded locking pins to secure the connection.
9. Mounting holes for alternative installation of the speaker with chains.
Important: Before any assembly, check that all mounting bracket components are complete, undamaged and work
correctly (split pins, screws, bolts, nuts, locking pins, steel hooks, retaining sockets in speakers, etc.). Should any
mounting bracket component be damaged, missing or not function properly, the mounting bracket should not be used.
10. Insert all three steel hooks of the EasyMount bracket into the corresponding retaining sockets on the speaker.
11. Slide the entire bracket towards the back of the speaker.
12. When installing the mounting bracket, ensure that the spring-loaded locking pins engage fully. Ensure that
locking pins are functioning correctly before every installation. For safety reasons, both locking pins must be
pulled upwards simultaneously to release the connection (two-hand release).
13. Before attaching the speaker to a traverse, tighten the T-screw on the mounting bracket No. 3. Using
traverse clamp No.1, suspend the speaker from a horizontal traverse in a suitable position, and fasten it into
place with wing nut No. 2.
14. Loosen T-screw No. 3 slightly (approximately 1 turn). To adjust the vertical dispersion of the speaker, lift the
speaker slightly and slide the notched mounting rail No.4 into the desired tilt position. Release the speaker to
allow the retaining pin No. 5 to engage in the corresponding notch.
15. Turn the speaker until the desired horizontal dispersion is achieved and tighten T-screw No. 3.
B
C
Colour:
Max. Load
Dimensions (W x H x D):
Weight:
Adam Hall GmbH · Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
Tel.: (+49) 60 81 / 94 19 0 · Fax: (+49) 60 81 / 94 19 1000 · eMail: mail@adamhall.com
1
2
9
4
6
3
5
7
9
7
8
10 11
13 14
Black
28 kg
230 mm x 240 mm x 430 mm
2.3 kg
EN
7
9
8
12
15