HEADRUSH CORE Schnellstartanleitung Seite 4

Rear Panel
Power Input: Connect this input to a power outlet using the included power cable.
1.
2. Power Switch: Press this button to turn HeadRush Core's power on/off.
Vent: Make sure this vent is unobstructed while using HeadRush Core.
3.
USB Type-B Port: Connect this USB port to a computer using a standard USB cable. This connection allows HeadRush
4.
Core to send and receive the digital audio signal to and from your computer. You can also use this connection to import
or export rigs, impulse responses, loops, block presets, setlists, and more. See the User Guide for more information.
USB Type-A Port: Connect a USB flash drive to this USB port for additional storage. A class-compliant USB device can
5.
also be connected to this USB port for external MIDI control.
Guitar Input (1/4"/6.35 mm, TS): Connect your guitar to this input using a standard instrument cable.
6.
7. Mic Input (XLR or 1/4"/6.35 mm, balanced): Connect a microphone to this input using a standard XLR or 1/4" (6.35 mm)
microphone cable. You can enable or disable +48V phantom power for these inputs in the Global Settings page.
Important: Only enable phantom power if your microphone requires it. Most dynamic microphones and ribbon
microphones do not require phantom power, while most condenser microphones do. Consult your microphone's
documentation to find out whether it needs phantom power.
Mic Input Gain: Use this knob to adjust the level of the Mic Input. View the current level of the microphone by double
8.
tapping the input block to make sure the level is not low or clipping.
External Amp Footswitch Output (1/4"/6.35 mm, TRS): Connect this output to the footswitch input of an external guitar
9.
amplifier to toggle channels or turn reverb on and off on the amplifier using the HeadRush Core.
IMPORTANT! Only connect this output to amplifiers that have a "short-to-sleeve" footswitch input. If you connect this
output to any other type of footswitch input, you may cause permanent damage to your equipment. If you are unsure if
your amplifier has a "short-to-sleeve" footswitch input, please consult the amplifier's manual or manufacturer to confirm
before attempting.
Aux Input (1/8"/3.5 mm, TRS): Connect an optional audio source (e.g., smartphone, tablet, etc.) to this input using a 1/8"
10.
(3.5 mm) stereo cable.
11. Expression Pedal Input (1/4"/6.35 mm, TRS): Connect an optional secondary expression pedal to this input using a
standard instrument cable.
Expression Pedal Toe Switch Input (1/4"/6.35 mm, TS): Connect the toe switch output of your optional expression pedal
12.
to this input using a standard 1/4" (6.35 mm) TS cable.
FX Send Output (1/4"/6.35 mm, TRS): Connect this output to the input of another effects module, an effect pedal, or the
13.
effects loop return of an amplifier.
14. FX Return Input (1/4"/6.35 mm, TRS): Connect this input to the output of another effects module, an effect pedal, or the
effects loop send of an amplifier.
Phones Output (1/8"/3.5 mm, TRS): Connect standard 1/8" (3.5 mm) stereo headphones to this output. Use the phones
15.
volume knob to control the volume level.
Outputs (1/4"/6.35 mm, TRS): Connect these outputs to the inputs of your amplifier, audio interface, etc. If you only need
16.
to use one output, use the one labeled Left/Mono.
17. Outputs (XLR): Connect these outputs to the inputs of your mixer, active loudspeaker, etc. If you only need to use one
output, use the one labeled Left/Mono.
18. MIDI Input (5-pin DIN): Use a standard MIDI cable to connect this input to the MIDI output of an optional external MIDI
device.
MIDI Output/Thru (5-pin DIN): Use a standard MIDI cable to connect this output to the MIDI input of an optional external
19.
MIDI device. You can set this output to be a standard MIDI output or MIDI throughput in the Global Settings page.
4