Werbung
Verfügbare Sprachen
Verfügbare Sprachen
magnet (Fig.7). We advise recipients having a flat base
(Fig.8A). This way you can use the power optimally.
Do not use recipients with a rough base to avoid
scratching the thermal surface of the top.
A very important factor in induction cooking is the dimension
of the pot compared to the plate used (Fig.8B). The
cooking zones allow the use of recipients with bases of
various diameters. It is, however, preferable to use the
appropriate cooking zone for the dimension of the pot:
- if pot diameter is 160 mm, the Pot.detection. is 90 mm
and the Pot.max is 180 mm;
- if pot diameter is 200 mm the Pot.detection is 120 mm,
and Pot. max. 210 mm.
SWITCHING THE COOKING TOP ON
• Connect the stovetops to the mains
• SWITCHING THE COOKING TOP ON
Press A key to switch the top on.
All the displays relative to the cooking zones switch on in
the
standby position.
The control unit remains active for 10 seconds.
If no cooking zone is selected within this time, the
ccoking top switches off automatically.
• SWITCHING THE COOKING AREA ON
Select the desired cooking zone and press or crawl one
of the E keys.
Press key E to go to position 9 (max. power) or to go to
position 1 (min. power).
The power of the single cooking zone can be adjusted
in 9 different positions and will be shown on the relative
luminous display E with a number from "1 to 9".
• ADJUST THE POWER OF COOKING
To increase / decrease the power of the cooking zone
selected, crawl in a clockwise / counterclockwise
E keys. The power can be set from 0 to 9.
• QUICK / BOOSTER HEATING
This function further reduces cooking time in a given area
taking the temperature to the maximum power for a
minute interval. At the end of this interval, the cooking
area power automatically returns to level
The use of this function is indicated for the short time heating
of large quantities of liquid (eg water for cooking pasta) or
dishes.
After selecting a cooking zone can be selected by
pressing the D booster function, this function for a time
of 10 minutes the plate selected feeds at
maximum power
.
• PAUSE
When at least one cooking zone is operating it is possible
to momentaneously pause the appliance switching off the
heating elements by pressing the C key. When the pause
function is active the relative led is on. The pause may
last for 10 minutes. If the status is not terminated within
this time the appliance switches off. The pause function
can be deactivated by pressing the C key and within 10
seconds any of the control keys. Previously programmed
timers will be stopped during the pause.
• TIMER
This function allows establishing the time (from 1 to 99
minutes) for automatically switching the selected cooking
zone off. Switch on at least one cooking zone and adjust
the temperature.
Press simultaneously the H and I key to enter the
timer function. Press either button to adjust the cooking
time is shown on its display. Select the required cooking
zone with one of the buttons and LED bar under the
diplay of the area activated, indicating the selection. Set
the power of the area between 1 and 9 keys with the
same E. Set at this point the desired sleep time using
the keys H or I timers in the area. The inclusion of the
timer with the clock symbol will appear next to the display
of the cooking zone selected. The countdown will be
displayed on the display above the keys H - I. The timer
will automatically turn off the cooking area and you will
hear a beep that can be turned off by pressing any of
the commands. To disable the timer, press the keys H
and I of the timer.
• EGG TIMER / REMINDER
To set a 'reminder time' press simultaneously the C and
D key. The led located at the bottom-center of the timer
display will be flashing. Set the 'reminder time' (from 1
to 99 minutes) by pressing the C or D key. An acoustic
signal will indicate the 'reminder time' expiration. Press
any key to stop the acoustic signal. The egg timer
remains active even if the appliance is switched off. In
order to disable the egg timer press simultaneously the
C and D key to enter the egg timer function. Press the
D key until reaching position
• RECALL
When the appliance has been switched off by mistake it
is possible to quickly recall the previously active settings
by pressing the on-off A key withing 6 seconds, then
pressing the C key within another 6 seconds. If the recall
function is available the relative led C will be enlighted
when the appliance is swithcehd on again.
• CONTROL PANEL LOCK
It is possible to block the controls to prevent the risk
of unintentional modification of the settings (children,
cleaning etc.). By pressing the B key, the controls are
blocked and the relative warning light switches on.
10
To release the controls and change the settings
(e.g.interrupt cooking), the B key must be pressed. The
9
.
cooking top can however be switched off even when the
controls block is activated. In this case the controls block
remains active when the top is switched on again.
• RESIDUAL HEAT
If the temperature of the cooking zone is still high (over
50°) after it has been switched off, the relative display will
indicate the
only switch off when the burn risk in no longer present.
• POT DETECTION
If the symbol
area displays, it means that:
1)The recipient being used is not suitable for induction
cooking.
2)The diameter of the recipient used is inferior to that
allowed by the appliance.
3) No recipient is present.
- 8 -
.
symbol (residual heat). The symbol will
should appear on one of the cooking
Werbung
