Sicherheitshinweise
▪
Beim Einsatz der Maschine stets Gehörschutz
tragen.
▪
Stets geeignete Schutzkleidung tragen. Schützen
Sie Ihre Hände, Haare und Kleidung vor dem
Erfassen durch rotierende Teile.
▪
Maschine nur mit ausgeschaltetem Ventil und
eingespanntem Werkzeug an das Druckluftnetz
anschließen.
▪
Maschine nicht am Druckluftschlauch tragen.
▪
Beachten Sie die Gefahr eines schlagenden
Druckluftschlauches !
▪
Fließdruck von 6,3 bar darf während des
Betriebs keinesfalls überschritten werden.
▪
Beachten Sie die Gefahr infolge von unerwartet
auftretenden Bewegungen der Maschine durch
Reaktionskräfte oder Bruch des eingesetzten
Werkzeuges !
▪
Halten Sie Ihre Hände fern vom eingesetzten
Werkzeug.
▪
Beachten Sie die Gefahr von Splitter, die bei Bruch
des eingesetzten Werkzeugs mit hoher
Geschwindigkeit wegfliegen können !
▪
Beachten Sie die Gefahr von unerwarteten
Bewegungen des Einsatz Werkzeuges !
Inbetriebnahme
▪
Das Werkzeug stets nur nach den jeweils
geltenden Vorschriften für handgeführte
Druckluftwerkzeuge betreiben. Lesen Sie vor
Benutzung den beiliegenden Sicherheitshinweis.
▪
Vor dem Anschluss der Maschine ist die
Druckluftleitung (der Druckluftschlauch) gut
durchzublasen, um eventuell vorhandene
Schmutzpartikel zu entfernen.
▪
Prüfen Sie vor Anschluss der Maschinen Ihre
Druckluft auf Wassergehalt. Wasser, Korrosion
etc. im Leitungsnetz verursachen Rost innerhalb
des Motors und damit einen hohen Verschleiß
bzw. Ausfall der Maschinen.
▪
Vorgeschriebene Luftqualität gemäß DIN ISO
8573-1, Qualitätsklasse 3 bereitstellen.
▪
Benutzen Sie eine Wartungseinheit, die so nahe
wie möglich an dem Maschine angebracht sein
sollte. Die Ölliefermenge auf 2-3 Tropfen (1
Tropfen = 15 mm³) pro Minute einstellen. Wir
empfehlen den Einsatz eines Nebelölers bzw.
Wartungseinheit von MANNESMANN DEMAG.
▪
An der Wartungseinheit einen Betriebsdruck von
max. 6,3 bar einstellen. Ölstand kontrollieren und
ggf. Öl nachfüllen.
▪
Maschine nach Beendigung des Arbeitsganges
ausschalten und nach Stillstand sicher ablegen.
Maschine von der Druckluftversorgung abschalten.
▪
Auf die richtige Lichte Weite des
Druckluftschlauches achten ! Siehe hierzu
Technische Daten der Maschine.
Safety instructions
▪
Always wear ear protection when working with the
machine.
▪
Always wear suitable protective clothing. Protect your
hands, hair and clothing from contact with rotating
parts.
▪
Only connect the machine with the compressed air
system when the valve is switched off and the tools
are restrained.
▪
Do not carry the machine by the compressed air pipe.
▪
Be aware of the danger of a flapping air hose.
▪
The operating pressure of 6 bar must by no means be
exceeded during operation.
▪
Please be aware of the inherent danger from
unexpected machine movements caused by
recoil/reaction forces or breakage of the working tool !
▪
Keep your hands away from the working tool.
▪
Please be aware of the danger from splinters which
can fly out at high speeds if there is a breakage of the
working tool !
▪
Please be aware of the danger from unexpected
movements of the working tool !
Commissioning
▪
Only use the tool in accordance with the respective
regulations that apply to the use of manually operated
compressed air tools. Please read the safety
instructions enclosed before use.
▪
Before the machine is connected, the compressed air
feed (the compressed air pipe) should be well blow
through to remove any dirt particles.
▪
Check your compressed air for water before the
machine is connected. Water, corrosion etc. in the pipe
system causes rust inside the motor and more wear
and/or failures of the machine.
▪
Supply specified air quality in accordance with DIN
ISO 8573-1, quality class 3.
▪
Use a maintenance unit which is placed as close as
possible to the machine. Set the oil supply quantity to
2-3 drops (1 drop = 15 mm
recommend the use of a fog oiling agent and/or
maintenance unit from MANNESMANN DEMAG.
▪
Set an operational pressure of max. 6.3 bar on the
maintenance unit. Check the oil level and refill if
necessary.
▪
Switch off the machine after use and place in a safe
place when not in use. Disconnect the machine from
the compressed air supply.
▪
Please ensure the correct clearance of the
compressed air pipe! See Technical data for the
machine.
3
) per minute. We