Connectivity Functions - Bosch GBH 18V-24 C Professional Originalbetriebsanleitung

24 | English
Working mode (22) indic- Functions
ator
In Favorite working mode, the power tool can be individually configured via a smartphone
lights up
app.
– The speed can be configured in several settings for different applications:
Practical Advice
The power tool with built-in Bluetooth
u
Module is equipped with a radio interface. Local oper-
ating restrictions, e.g. in aircraft or hospitals, must be
observed.
In areas in which the Bluetooth® wireless technology
u
must not be used, the Bluetooth® Low Energy Module
must be switched off via the app.
Setting the drilling depth (see figure E)
You can use the depth stop (14) to set the required drilling
depth X.
– Press the button for depth stop adjustment (5) and insert
the depth stop into the auxiliary handle (13).
The fluting on the depth stop (14) must face downwards.
– Insert the SDS-plus application tool into the SDS-plus tool
holder (2) to the stop. Otherwise, the movability of the
SDS-plus drilling tool can lead to incorrect adjustment of
the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
Overload clutch
If the application tool jams or snags, the power trans-
u
mission to the drill spindle will be interrupted. Always
hold the power tool firmly with both hands to with-
stand the forces this may create and adopt a position
with stable footing.
Switch the power tool off immediately and remove the
u
application tool if the power tool becomes blocked.
Switching on when the drilling tool is blocked may
cause high torque reactions.
Rapid shut-off (KickBack Control)
The rapid shut-off function (KickBack
Control) gives the user greater control
over the power tool and offers them bet-
ter protection than power tools that do
not have Kickback Control. If the power
tool suddenly and unforeseeably rotates
around the drilling axis, it will switch off,
the rapid shut-off indicator (19) will light
up red and the worklight (12) will flash.
When rapid shut-off is activated, the
status indicator (17) flashes red.
– To switch the tool back on, release the on/off switch (9)
and then press it again.
1 609 92A 866 | (27.09.2022)
low/medium/high (100 % of the maximum speed) speed
Inserting screwdriver bits (see figure F)
u
®
Low Energy
A universal holder (24) with SDS-plus shank (accessory) is
required to work with screwdriver bits.
– Clean and lightly grease the insertion end of the shank.
– Insert the universal holder into the tool holder while turn-
– Check that it is locked by pulling the universal holder.
– Insert a screwdriver bit in the universal holder. Only use
– To remove the universal holder, slide the locking sleeve

Connectivity functions

System Requirements for Using the App
System Requirements
Mobile device (tablet,
smartphone)
Installing and Setting up the App
You will need to install the device-specific app before you
can use the connectivity functions.
– Download the app from the corresponding app store
App name
Bosch Toolbox
– Then select the MyTools or Connectivity sub-item in the
– The display of your mobile device shows you all of the
Data Transfer via Bluetooth
The built-in Bluetooth
regular intervals. Depending on ambient conditions, multiple
transmission intervals may be required before the power
Only apply the power tool to the screw/nut when the
tool is switched off. Rotating tool inserts can slip off.
ing it until it locks automatically.
screwdriver bits that fit the screw head.
(4) backwards and remove the universal holder (24)
from the tool holder.
(Apple App Store, Google Play Store).
Note: You will need to have a user account with the relev-
ant app store to do this.
iOS
app.
subsequent steps required to connect the power tool to
the mobile device.
®
®
Low Energy Module sends a signal at
Android 6.0 (and newer)
iOS 11 (and newer)
Android
Bosch Power Tools