Before Starting The Equipment - Robust RB-MG 135 Originalbetriebsanleitung

Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

5.1 Taking out the accessories (Fig. 4)
To be able to take out the accessories you must
pull the accessory mount (a) upwards.
5.2 Inserting the various tools (Fig. 3)
Before inserting a tool (and before each tool
change) switch of the drive unit and pull the pow-
er plug.
Anl_RB_MG_135.indb 18 Anl_RB_MG_135.indb 18
GB
1. Press the locking knob (4) and turn the collet
chuck until the bolt locks into place.
2. Undo the collet chuck nut (3).
3. Insert the required tool into the sleeve and
tighten the collet chuck nut (3).
5.3 Installing the fl exible shaft (Figs. 3/5)
•
Unscrew the cover (5) from the front of the
equipment.
•
Undo the collet chuck nut (3).
•
Insert the internal schaft (a) of the flexible
shaft into the collet chuck (3).
•
Tighten the collet chuck nut (3).
•
Now tighten the ring (b) on the multi-tool.
5.3.1 Inserting the various tools in the fl exible
shaft
1. Press the locking pin (18) into the hole in the
fl exible shaft (13) and turn the shaft until the
pin latches in place.
2. Now undo the collet chuck nut.
3. Insert the required tool into the clamping
sleeve as far as the stop and screw the collet
chuck nut tight.
5.4 Using the stand (Fig. 6)
•
Fit the stand to a workbench
•
The stand is adjustable in height and can be
•
adjusted as shown in Fig. 6.
•
The multi-tool can now be attached to the
stand.
6. Using the tool for the fi rst time
•
Make sure that the drive unit is switched off.
•
Check that the mains voltage specified on the
rating plate of the power supply unit is the
same as your mains supply. Only then should
you insert the plug of the power supply unit
into a socket-outlet.
6.1. ON/OFF switch (Fig. 3)
Switch on the drive unit with the power switch (1).
6.2. Speed selector (Fig. 3)
The required speed can be set with the speed
control (2).
The correct speed depends on the tool used and
the type of material being processed.
- 18 -
6.3
•
•
6.4
•
•
•
•
•
7. A
7.1
1 G
2 G
3 G
7.2
1 C
2 C
7.3
1 C
2 C
3 C
4 C
7.4
1 G
2 Fe
7.5
1-5
7.6
1 D
2 C
3 G
4 G
5 Po
04.06.12 14:57 04.06.12 14:57