Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Type of lamps
•
The lamp must have a length of 185.7 mm
•
Lamphouse R7-S
•
Power can be 625 W, 1000 W ou 1250 W.
•
Alimentation : 230 V.
Electrical Connection
Your spotlight has been designed to operate at a maximum voltage of
220 V - 240 V.
It is delivered with a silicon 3-core cable (cross-section 3 x 1.5 mm
without plug. The length of this cable is 2 metres.
For your safety, check that the earth-conductor (green/yellow conductor)
is ALWAYS connected to the earth terminal.
Assembly
Your spotlight can be suspended from a carrier bar by means of a A6,
A20, A25 or A30 suspension hook; it may also be mounted on a tripod.
These accessories are available as an option.
You should avoid placing the spotlight close to inflammable materials.
Do not exceed the maximum angles of inclination stated on the index
plate. ALWAYS use the safety cable by passing it into the suspension
yoke.
In accordance with the safety regulations, the use of a 3 mm safety grid
or a glass filter with 12 mm safety grid is compulsory to prevent pieces
of glass from the lamp falling.
Assembly of the accessories
Some accessories can be mounted on the spotlight :
•
safety grille for the lamp
•
cassette for filter frame for colour glass filters
•
filter frame for colour glass filters
•
vertical barndoors
•
horizontal brandoors
•
assembly bar for 4 spotlights
Safety grid for the lamp
Unscrew the 2 screws retaining
the reflector; insert the safety grid
into the lateral slides of the
spotlight; screw those screws
again.
Cassete for filter frame for colour glass filters
Unscrew the 4 screws retaining
the reflector; put the cassette with
his 4 captive screws.
Lighting Technologies
Filter frame for colour glass filters
The lamellated filters are fitted
with two high temperature
adhesive strips; do not remove
them.
Insert the lamellated filter in the
metallic filter frame; check that
the safety grid is well fitted in the
metallic frame; fold the safety clip
back. Insert the filter frame into
2
),
the two lateral slides; check that
the safety grid is positionned
before the lamellated glasses.
Vertical barndoors
Unscrew the 2 screws located on
the right lateral slide; put on the
right barndoor and screw these
screws. Follow the same
procedure for the left barndoor.
Horizontal barndoors
Unscrew the two upper screws
retaining the reflector; put on the
upper barndoor; screw those
screws again.
Follow the same procedure for
the lower barndoor.
Fixing points are directely
accessible (without unscrew the
screws retaining the reflector) to
install the horizontal barndoors
on the cassete for filter frame.
Bar for assembly of 4 spotlights
An "U section" bar is available to fit 4 spotlights horizontaly; it's
delivered with 4 fixing screws. The hole in the centre allows to suspend
the general fitting from a carrier bar by means of fixing bolts; it can also
be mounted on a tripod. These accessories are available as optional
extras.
Maintenance
We recommend that the reflector should be cleaned each time you
replace the lamp.
•
Disconnect the spotlight.
•
Allow the spotlight to cool.
•
Remove the safety grille or the filter frame.
•
Carefully remove the lamp.
•
Clean the reflector using a clean, non-fluffy cloth impregnated with
alcohol.
•
Replace the lamp and the safety grid.
Replace any cracked protective shield!
Angles utilisation
•
From the vertical position
Lampe
Without Filter Frame
625 W
0 à 90°
1000 W
0 à 90°
1250 W
0 à 45°
HF / LF 1000
With Filter Frame
& Glass Filter
0 à 90°
0 à 60°
-
Page 7
Werbung
Inhaltsverzeichnis
