Philips AVENT SCD860/01 Bedienungsanleitung Seite 3

8 Insert the appliance plug into the appliance plug socket in the
temperature and humidity sensor unit and insert the adapter into
a wall socket. Now your baby monitor is ready for use (Fig. 12).
WiFi status light signals
1 Off
- The baby monitor is off
2 Orange
- Flashes fast: the baby monitor is starting up.
- Flashes slowly: the baby monitor is upgrading its firmware.
Do not switch the baby monitor off during the firmware upgrade.
Note: The WiFi status light might switch off shortly during the firmware upgrade.
- Solid: the camera of the baby monitor is ready to read the WiFi QR
code generated by your smartphone or tablet.
3 Green
- Flashes slowly: the WiFi QR code has been read successfully.
- Solid: the baby monitor is connected to the WiFi network.
4 Red
- Flashes slowly: the WiFi password entered is wrong.
- Solid red: the baby monitor fails to connect to the WiFi network.
Resetting the baby monitor
The baby monitor has a reset button on the back. When you press this
button the baby monitor is reset to its factory default settings.
Note: Always reset the baby monitor by pressing the reset button and delete
your account before you transfer the baby monitor to someone else.
This is necessary to protect your privacy.
How to reset to factory default settings
While the baby monitor is on, press the reset button on the back
1
of the baby monitor with a paperclip or another pointed object.
It is recommended to do this when the baby monitor is connected
to your WiFi network (Fig. 13).
Keep the reset button pressed until the baby monitor beeps.
2
What to do after a reset to factory default settings
After the baby monitor has been reset, you need to reconnect it to
the WiFi network. If you invited other people to access the baby monitor,
you need to invite them again.
Cleaning and maintenance
- Unplug the baby monitor before you clean it.
- Clean the baby monitor with a dry cloth.
- Do not use aggressive cleaners, scouring agents, petrol, acetone etc.
to clean the plastic housing of the appliance.
- Do not use cleaning spray or liquid cleaners.
Replacement
If the baby monitor is damaged, contact the Consumer Care Centre in your
country (see chapter 'Guarantee and support').
Adapter
Only replace the adapter of the baby monitor with a Philips adapter of the
original type. See chapter 'Ordering accessories' for information on ordering
a new adapter.
Wall mounting bracket
If necessary, you can order a spare wall mounting bracket for this baby
monitor (see chapter 'Ordering accessories').
Ordering accessories
To buy accessories or spare parts, visit www.shop.philips.com/service
or go to your Philips dealer. You can also contact the Philips Consumer Care
Centre in your country.
Guarantee and support
If you need information or support, please look in the support menu of
your app, visit the Philips website at www.philips.com/support or read
the separate worldwide guarantee leaflet.
Frequently asked questions
For more frequently asked questions, check the relevant section in the app.
All manuals and user guides at all-guides.com
Question Answer
You can find the user manual online at www.philips.com/
Where can I
find the user ugrow. The user manual is also available inside the
manual? app. Tap on 'Support' in the left tray to open the user
manual.
I have problems Make sure that you hold the WiFi QR code at approx.
making my baby 20 cm/8 inch distance from the lens. Try moving the
monitor read smart device slightly up or down or left or right to ensure
the QR code the WiFi QR code is directly in front of the baby monitor.
on my smart You can also try moving the smart device closer to or
device. What further away from the baby monitor lens to allow proper
can I do? focussing. Make sure that there is enough light in the
room, but avoid too bright light. When the baby monitor
has read the WiFi QR code, it beeps to confirm.
Perhaps you did not remove the protective foil from
the baby monitor lens. Remove the foil.
Perhaps part of your hand covers the WiFi QR code.
Hold your device in such a way that your hand does
not cover the WiFi QR code.
I cannot Please check if any of the following factors prevent
download and a smooth download. Is your WiFi signal stable and
install the app. strong enough? Does your smart device run on iOS
What can I do? 7 or higher, or Android 4.1 and higher? Do you have
enough space left on your smart device to save the
app? Did you enter the correct password for the App
Store or Google Play?
Recycling
- This symbol on a product means that the product is covered by
European Directive 2012/19/EU. Inform yourself about the local
separate collection system for electrical and electronic products.
Follow local rules and never dispose of the product with normal
household waste. Correct disposal of old products helps prevent
negative consequences for the environment and human health (Fig. 14).
Specifications
General
AC power adapter:
- Rated input 100-240 V
- Rated frequency 50-60 Hz
- Rated output - adapter 5V DC , 1 A
Connectivity: WiFi 802.11 b/g/n, 2.4 GHz
Apps
- Operating system iOS 7 or higher (excluding iPhone 4 or
lower), or Android 4.1 and higher
For the latest information on device
compatibility, please visit www.philips.com/
ugrow.
Lens
Focus mode
Focus range
Aperture
Digital zoom
Night mode
Sensors
Temperature sensor
Humidity sensor
Video
Resolution
Video format
Fixed
0.7 - 5 metres
F2.8
2x
IR LED, range 4 metres
0°C - 40°C
10% - 80% RH
up to 720p (HD)
H.264