Chicago Pneumatic CP7225-3 Bedienungsanleitung Seite 4

EN
English
INSTRUCTION MANUAL
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes
shown in the diagram below.
3. Do not install a quick coupler directly into the sander
throttle handle.
1/4"NPT
3/8" (10mm)
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
drops per minute. If an air line lubricator cannot be used,
add air motor oil to the inlet once a day.
Maintenance
1. Disassemble and inspect air motor and orbital assembly
every three months if the tool is used every day. Replace
damaged or worn parts.
2. High wear parts are underlined in the parts list.
3. To keep downtime to a minimum, the following service kits
are recommended:
Tune-Up Kit
8940163459 (Incl: 7, 17, 18, 22, 24, 25, 32, 47)
Hose Adaptors for CV Palm Sanders
6153501170 (Incl: Vacuum Hose Adaptor
Ø25 (1") / Ø32 (1 1/4"))
6158044480 (Incl: Vacuum Hose Adaptor
Ø25 (1") / Ø28 (1 1/8"))
Maintenance Kit
8940163460 (Incl: Wrenches for Pad, Motor Kit and Lock
Ring)
Copyright 2009, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not
covered by Warranty or Product Liability.
All manuals and user guides at all-guides.com
1/2" (12mm)
REGULATOR
90
0 130
1/2" (12mm)
FILTER
LUBRICATOR
CP7225-3 & CP7255-3 Series
EC DECLARATION OF CONFORMITY
We, Chicago Pneumatic Tool Co. LLC,13325 Carowinds
Blvd., Charlotte, NC 28273 USA, declare under our sole
responsibility that the product to which this declaration relates,
is in conformity with the requirements of the Council Directive
of June 1998 on the approximation of the laws of the Member
States relating to machinery (98/37/EC).
Machine Name CP7225-3 & CP7255-3 Series Random
Orbital Sander
Machine Type Power tool equipped with a flexible disc fitted
with abrasive paper for sanding - No other use is permitted
Serial No. Tools with No. 2009-001-P or higher
Technical Data
Pad Diameter 3in. (70mm)
Free speed 12,000 RPM
Air pressure 90 psi (6.3 bar)
Spindle size 5/16"-24
Air Consumption 14.5 CFM (5 l/s)
Harmonized Standards Applied EN792-8
National Standards Applied ISO 8662-8, EN ISO 15744
Name and Position of Issuer Bruno Blanchet, General
Manager
Signature of Issuer_______________
Date of Issue December 15, 2008
Noise & Vibration Declaration*
Sound pressure level 76 dB(A), uncertainty 3 dB(A), in
accordance with EN ISO 15744. For sound power, add 11
dB(A).
Vibration value < 2.5 m/s
2
For making estimates of daily vibration exposures, useful
information may be found in CEN/TR 15350: 2006,
"Mechanical vibration - Guideline for the assessment of
exposure to hand-transmitted vibration using available
information including that provided by manufacturers of
machinery"
*These declared values were obtained by laboratory type testing in
compliance with the stated standards and are not adequate for use
in risk assessments. Values measured in individual work places
may be higher than the declared values. The actual exposure
values and risk of harm experienced by an individual user are
unique and depend upon the way the user works, the workpiece
and the workstation design, as well as upon the exposure time and
the physical condition of the user. We, Chicago Pneumatic, cannot
be held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have no
control.
Random Orbital Sander
, re. ISO 8662-8.