newmotion Business Pro View 2.2 Installationsanleitung Seite 12

3. PRODUCT OVERVIEW
3.5 BACKOFFICE CONNECTIONS
BUSINESS PRO (VIEW)
The Business Pro View can be connected to the
NewMotion backoffice in three different ways:
1. Ethernet connection
2. GPRS 2G
3. 2/3/4G with NewMotion mobile router
The Business Pro View will connect to the NewMotion
backoffice so settings can be changed remotely and
for remote support. Without the back office connection
none of our online services can be used.
In groups of multiple Business charge points there
should be exactly one Business Pro (View). Connecting
a Business Pro (View) to another Business Pro (View) is
not possible.
3.5.1 BUSINESS PRO VIEW
– ETHERNET / NEWMOTION MOBILE ROUTER
Connecting the Business Pro View to ethernet or mobile
router can be done by connecting the network to the left
UTP Ethernet data port with a cable max 50 meter long.
(Mobile)
Router
09.......
(PRO)
Settings might have to be changed in the network
to allow the Business Pro View make a successful
connection to NewMotion backoffice.
The network should have:
- DHCP
- Port TCP 80 and 443 should be opened
- FTP port 21 should be opened for the Business Pro
- All opened ports should be outbound
FTP is needed to update the firmware of the charge
point and exchange diagnostics.
3.5.2 BUSINESS PRO VIEW - GPRS 2G
The Business Pro View will first attempt to connect
online through the left UTP Ethernet data port. If no
connection can be made the Business Pro View will try
to set up a GPRS connection. The connection will only
be possible if the signal strength is -80dBm or better for
Vodafone (or partners).
INSTALLATIEHANDLEIDING – P12
INSTRUCTION MANUAL – P12 | P12
3.6 BUSINESS LITE VIEW -
BACKOFFICE CONNECTION
The Business Pro (View) will handle all communication
with the backoffice for the Business Lites. This means
that a Business Lite (View) without being connected to a
Business Pro (View) will not connect to the NewMotion
backoffice and remote settings can not be changed
or remote support can not be provided. Without the
backoffice connection none of our online services can
be used.
The Business Lite (View) should, directly or indirectly,
be connected to the right hand side UTP data port of
a Business Pro (View). An indirect connection can be
through a switch or another Business Lite (Daisy chain).
3.6.1 BUSINESS LITE - DAISY CHAIN CONFIGURATION
The Business Lites have two ethernet ports which can
daisy chain the connection to the next Business Lite.
The left port should be closest to the Pro and the right
port should be going to the next Lite (see figure below).
Optional
(Mobile)
Router
The daisy chain configuration can be used up to
15 charge points. For higher quantities NewMotion
strongly recommends to use a star configuration. A star
configuration also limits possible downtime if that is
desired and can also be used to minimize downtime of
backoffice connection and dynamic loadbalancing.
3.6.2 BUSINESS LITE - STAR CONFIGURATION
In a star configuration all Lites are connected from the
left UTP Ethernet data port to a switch.
From the right hand side of the Pro there is a cable going
to the same switch (please note that the left port of the
Pro is reserved for ethernet or mobile router connection,
see backoffice connection business Pro). Only one Pro is
allowed to be connected to the switch.
Optional
(Mobile)
Router
VERSION 0129NM02INT01
095NM21INT02
09....... 08....... 08....... 08....... 08.......
(PRO) (LITE) (LITE) (LITE) (LITE)
Switch
09....... 08....... 08....... 08....... 08.......
(PRO) (LITE) (LITE) (LITE) (LITE)