Seite 1
E 170 /230 V AC DE Anschlussplan GB Wiring diagram E 170 /24 V DC E 212 R1 /230 V AC E 212 R /230 V AC E 212 /24 V DC DE Linearantrieb GB Linear drive 151531-01...
E 170 / E 212 R1 / E 212 R / E 212 Inhaltsverzeichnis Symbole und Darstellungsmittel ............3 Sicherheitshinweise ................3 Produkthaftung........................3 Allgemeine Sicherheitshinweise..................4 Montagehinweise ......................4 Leitungsverlegung und elektrischer Anschluss .............5 Sicherheitsbewusstes Arbeiten und Benutzen ............5 Prüfen der montierten Anlage ..................6 Entsorgung der Fensteranlage ............6 Wartung .....................6 Elektrischer Anschluss ................8...
E 170 / E 212 R1 / E 212 R / E 212 Symbole und Darstellungsmittel Symbole und Darstellungsmittel Warnhinweise In dieser Anleitung werden Warnhinweise verwendet, um Sie vor Sach- und Personenschäden zu warnen. Lesen und beachten Sie diese Warnhinweise immer. Befolgen Sie alle Maßnahmen, die mit dem Warnsymbol und Warnwort gekennzeichnet sind.
Produktleistung, Produktwartung, Informations- und Instruktionspflich- ten) zu beachten. Die Nichtbeachtung entbindet den Hersteller von seiner Haftungspflicht. à Nur Sachkundige, die von GEZE autorisiert sind, dürfen Montage, Funk- tionsprüfung und Wartung durchführen. Eigenmächtige Veränderungen an der Anlage schließen jede Haftung von GEZE für daraus resultierende Schäden aus.
Höhe von mindestens 1,5 m und unzugänglich für die Öffentlichkeit angebracht sein. Bei Montage beachten: à Bei Kippfenstern eine geeignete Fangsicherung verwenden (z.B. GEZE Sicherheitsschere Nr. 35) à Zur Befestigung dürfen nur Original-Konsolen verwendet werden. à Zur Montage geeignete Befestigungselemente benutzen. Emp- fehlungen finden sich in den Montageanleitungen. Sicherstel- len, dass die Befestigungselemente im Profil für einen sicheren...
2,5 m zu prüfen und durchzuführen. Eine Maßnahme ist z.B. die Verwendung eines Schalters mit Aus-Vor- einstellung (z.B. GEZE Lüftertaster LTA-LSA Mat.Nr. 118476). Bei Kindern oder Personen mit eingeschränktem Urteilsvermögen muss ein Schlüs- selschalter mit Aus-Voreinstellung verwendet werden (z.B. GEZE Mat.Nr.
à Kabel Die Teile entsprechend den gesetzlichen Bestimmungen entsorgen. Wartung GEZE schreibt eine regelmäßige Wartung (mindestens 1x jährlich) vor. Diese ist von einem Sachkundigen auszuführen. Dabei müssen die Funktion sowie der Zustand der Mechanik (Ungleichgewicht oder Anzeichen von Verschleiß, Beschädigung von Befestigungsteilen) und der elektrischen Anschlüsse überprüft werden.
Elektrischer Anschluss E 170 / E 212 R1 / E 212 R / E 212 Elektrischer Anschluss Gefahr durch elektrischen Strom! GEFAHR! Beim Anschluss des Antriebs sicherstellen, dass keine Netzspannung an den Anschlussklemmen anliegt! E 170 / 230 V E 170 /24V E 170 E 212 E 212 R /230 V...
E 170 / E 212 R1 / E 212 R / E 212 Technische Daten Technische Daten 6. 1 Technische Daten E 170 Hauptmaße Mechanische Daten E 170 /230 V AC E 170 /24 V DC max. Zug- und Druckkraft [N] 1500 1500 Hubgeschwindigkeit [mm/s] Endlagenabschaltung...
Technische Daten E 170 / E 212 R1 / E 212 R / E 212 6.2 Technische Daten E 212 Hauptmaße Mechanische Daten E 212 R1 230 V / E 212 /24 V DC E 212 R 230 V AC max. Zug- und Druckkraft [N] 1500 1500 Hubgeschwindigkeit [mm/s]...
E 170 / E 212 R1 / E 212 R / E 212 Hub-/Endlageeinstellung 7. 1 E 170 Siehe Montageanleitung ID. 128689 (40422-9-0950). 7.2 E 212 LED (grün) Einstellschraube Hub Der Hub ist ab Werk auf 52 mm eingestellt. Hub entsprechend Beschlaghub einstellen und prüfen. Einstellwert = Beschlaghub -2 mm.
Seite 12
E 170 / E 212 R1 / E 212 R / E 212 Contents Symbols and means of representation ...........3 Safety instructions ..................3 Product liability ........................3 General safety precautions ....................4 Installation notes .......................4 Routing cables and electrical connection ..............5 Safety-conscious working and usage ................6 Inspection of installed system ..................6 Disposal of the window unit ...............7 Maintenance .....................7...
E 170 / E 212 R1 / E 212 R / E 212 Symbols and means of representation Symbols and means of representation Warnings In these instructions, warnings are used to warn against material damage and injuries. Always read and observe these warnings. Observe all the measures that are marked with the warning symbol and warning word .
à GEZE shall not be liable if devices from other manufacturers are used with GEZE equipment. Use only original GEZE parts for repair and main- tenance work as well.
During installation, heed the following: à With bottom-hung windows, use a suitable collecting safety device (e.g. GEZE safety scissor no. 35). à Only genuine consoles may be used for attachment. à Use suitable fixing elements for installation. Recommendations can be found in the installation instructions.
OFF default setting must be used (e.g. GEZE Mat. No. 117996 for SCT, 090176 for cylinder). The switch has to be mounted so that the points of danger can be seen.
Dispose of the parts in accordance with the statutory regulations. Maintenance GEZE prescribes regular maintenance (at least once a year). This is to be carried out by a suitably qualified person. In the process the operation as well as the condition of the mechanical equipment (imbalance or signs of wear, damage to fastening parts) and the electrical connections are to be checked.
Electrical connection E 170 / E 212 R1 / E 212 R / E 212 Electrical connection Danger of electric shock! DANGER! When connecting the drive, make sure there is no mains voltage at the supply terminals! E 170 / 230 V E 170 /24V E 170 E 212...
E 170 / E 212 R1 / E 212 R / E 212 Technical data Technical data 6. 1 Technical data E 170 Main dimensions Mechanical data E 170 /230 V AC E 170 /24 V DC Max. tensile force and force of pressure [N] 1500 1500 Stroke speed [mm/s] End position cut-off Limit switch...
Electrical connection E 170 / E 212 R1 / E 212 R / E 212 6.2 Technical data E 212 Main dimensions Mechanical data E 212 R1 230 V / E 212 /24 V DC E 212 R 230 V AC Max. tensile force and force of pressure [N] 1500 1500 Stroke speed [mm/s] End position cut-off...
E 170 / E 212 R1 / E 212 R / E 212 Stroke/end position setting Stroke/end position setting 7. 1 E 170 See mounting instructions ID. 128689 (40422-9-0950). 7.2 E 212 LED (green) Setting screw stroke The stroke is set to 52 mm in the factory. Set and check the stroke according to fitting stroke Setting value = Fitting stroke –...
Seite 22
E 170 E 212 R1 230V 4 x 1,5 mm LTA-LSA (ID: 118476) 3 x 1,5 mm 230 V AC 230 V AC 230 V AC GN/YE...
Seite 23
E 212 R 5 x 1,5 mm LTA-230 (ID: 118474) 5 x 1,5 mm 3 x 1,5 mm 230 V AC 230 V AC 230 V AC 230 V AC 230 V AC GN/YE A-II...
Seite 24
E 170 E 212 3 x 1,5 mm 24 V DC 24 V DC 24 V DC A-III...
Seite 29
Notizen/Notes E 170 / E 212 R1 / E 212 R / E 212...
Seite 30
Notizen/Notes E 170 / E 212 R1 / E 212 R / E 212...
Seite 31
Notizen/Notes E 170 / E 212 R1 / E 212 R / E 212...
Seite 32
Germany China Russia GEZE Sonderkonstruktionen GmbH GEZE Industries (Tianjin) Co., Ltd. OOO GEZE RUS Planken 1 E-Mail: chinasales@geze.com.cn E-Mail: office-russia@geze.com 97944 Boxberg-Schweigern www.geze.com.cn www.geze.ru Tel. +49 (0) 7930 9294 0 Scandinavia – Sweden GEZE Industries (Tianjin) Co., Ltd. Fax +49 (0) 7930 9294 10...