Personal Protective Equipment - Husqvarna 122HD45 Bedienungsanweisung

• Watch out for stumps of branches that can be thrown
out during cutting.
• Listen out for warning signals or shouts when you
are wearing hearing protection. Always remove your
hearing protection as soon as the engine stops.
• Never work from a ladder, stool or any other raised
position that is not fully secured.
• Always use both hands to hold the product. Hold the
product in front of your body.
• If any foreign object is hit or if vibrations occur stop
the product immediately. Disconnect the spark plug
cap from the spark plug. Check that the product is
not damaged. Repair any damage.
• Ensure that the spark plug cap and ignition lead are
undamaged to avoid the risk of electric shock.
• Check that all nuts and screws are tight.
• Make sure the gearbox is lubricated correctly. Refer
To lubricate the gear housing on page 12 .
to
• The gearbox gets hot when the product has been
in use. To avoid burning yourself do not touch the
gearbox.
• All covers and guards must be fitted before starting.
• If the blades get stuck, they can be loosened by
sticking the combination wrench into the gearbox.
Stick the combination wrench into the gearing and
turn it back and forth. Refer to
housing on page 12 .
• The transport guard should always be fitted to the
cutting unit when the product is not in use.

Personal protective equipment

WARNING:
instructions that follow before you use the
product.
• Always use approved personal protective equipment
when you use the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
• Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
• Use approved eye protection. If you use a visor,
you must also use approved protective goggles.
Approved protective goggles must comply with the
ANSI Z87.1 standard in the USAs or EN 166 in EU
countries.
(Fig. 10)
• Use gloves when necessary, for example when you
attach, examine or clean the cutting equipment.
(Fig. 11)
• Use sturdy non-slip boots or shoes.
(Fig. 12)
6
To lubricate the gear
Read the warning
• Use clothing made of a strong fabric. Always use
heavy, long pants and long sleeves. Do not use
loose clothing that can catch on twigs and branches.
Do not wear jewelry, short pants, sandals or go with
bare feet. Put your hair up safely above shoulder
level.
• Keep first aid equipment close at hand.
(Fig. 13)
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
• Do not use a product with defective safety devices.
• Do a check of the safety devices regularly. If
the safety devices are defective, speak to your
Husqvarna service agent.
To do a check of the throttle trigger lockout
1. Make sure that the throttle trigger lockout (A) and
throttle trigger (B) move freely and that the return
spring operates correctly. (Fig. 14)
2. Push down the throttle trigger lockout and make
sure that it goes back to its initial position when you
release it. (Fig. 15)
3. Release the throttle trigger lockout and make sure
that the throttle trigger is locked at idle speed
position. (Fig. 16)
4. Start the engine and apply full throttle.
5. Release the throttle trigger and make sure that the
blades stop fully.
WARNING:
when the throttle trigger is in the idle
speed position, adjust the idle speed.
Refer to
page 11 .
To do a check of the stop switch
1. Start the engine.
2. Push the stop switch to the stop position and make
sure that the engine stops.
WARNING:
automatically goes back to start position. To
prevent accidental start, remove the spark
plug cap from the spark plug when you
assemble or do maintenance on the product.
To do a check of the hand guard
The hand guard prevents injuries from the blades.
1. Stop the engine.
2. Make sure that the hand guard is attached correctly.
Read the warning
If the blades move
To adjust the idle speed on
The stop switch
994 - 013 - 24.06.2022