Grundig UMS 15 Servicehandbuch Seite 10

SETTINGS
____________________________________________________________________________
Setting the time
When the stereo is connected to the mains supply and the time has not been set,
the time display flashes.
Note:
Perform the setting in switched-off state.
1 1:20
1
Activate time-setting function by pressing »
down.
– In the display, »
2 Press » MEMORY« and set the hour with »
3 Press » MEMORY« and set the minute with »
15:00
4
Confirm input with » MEMORY«.
Note:
The time must be reset after a power failure or when the mains plug is
pulled out.
Setting the time for 12-hour display
14:00 1 Switch on stereo system by pressing »
2 Press »SOURCE« until »
| __ | __ | __ | __ | __ | __ | __ | __
I
I I I 3 Activate the time-setting function by pressing »
VOLUME I I I I
| __ | __ | __ | __ | __ | __ | __ | __
– In the display, for example, » I 4 : 0 0 « appears.
PM 02.00
4
Press » MEMORY« and hold down while pressing »
– » P M « appears briefly in the display; the time has been switched to
12-hour display.
| __ | __ | __ | __ | __ | __ | __ | __
I I I
I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I I
Note:
Repeat procedure to set for 24-hour display.
CLOCK TIMER « and holding
« flashes.
– VOLUME + «.
– VOLUME +«.
ON «.
TAPE
« appears in the display.
«.
CLOCK TIMER
II «.
SETTINGS
____________________________________________________________________________________
Searching for and saving a radio station – with the
automatic search
TUNER
Note:
MHz
In this mode, no more than 5 seconds may elapse between the pressing of
the various keys.
| __ | __ | __ | __ | __ | __ | __ | __
I I I
I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I I
1 Switch on stereo system with »
FM 87.50
2
Select desired frequency range (FM, MW or LW) with »
MHz
– In the display, » F M 8 7 . 5 0 « appears, for example.
3
Start the automatic station search for the FM range by pressing and holding
| __ | __ | __ | __ | __ | __ | __ | __
I I I
I I I I
| __ | __ | __ | __ | __ | __ | __ | __ VOLUME I
down » TUNING + –
– The station search begins, searches the frequency band for stations and
stops at the next radio station.
– The frequency of the station can be adjusted step-by-step (500 kHz) with
»a a 5 a
« or
FM PR:02
MHz
PROG. 4 Press » MEMORY« and select the desired channel position (1 to 24 in the
ST
FM range, 1 to 12 in the MW and LW range) with
»s 6 s s« on the stereo system or with »
| __ | __ | __ | __ | __ | __ | __ | __
I I
I I I (two-digit input, for example »
VOLUME I I I
| __ | __ | __ | __ | __ | __ | __ | __
– In the display, the selected channel position appears, for example
» F M P R : 0 2 «.
5
Save radio station with » MEMORY«.
6 To tune into other radio stations in the FM range, repeat procedure from
point 3 , for the »
«.
TUNER /BAND
TUNER /BAND «.
« on the stereo system.
»s 6 s s« on the remote control.
»a a 5 a
« or
1 ... 0 « on the remote control
« for channel position 4).
0 4
MW LW
« and » « ranges, repeat from point 2.