Multi-Source Mixing - Yamaha MT400 Bedienungsanleitung

26

Multi-Source Mixing

The mixer section of the MT400 enables you to control input signals and tape playback signals
simultaneously. For example, you can mix external sound sources with tape tracks. This
technique is useful when you wish to add pad or decorative notes to the introductory part of a
completed song. This section explains how to mix the sound sources connected to MIC/LINE
INPUTs 1 and 2 in addition to the tape tracks.
1
5
2
7
1
Connect the sound sources to MIC/LINE
INPUTs 1 and 2.
2
Set the [INPUT-FLIP] switches on Input
Channel 1–4 to "TAPE (
With the [INPUT-FLIP] switches set to "TAPE (
the MIC/LINE INPUT signals are sent to the Stereo
bus as follows.
MIC/LINE INPUTs 1 and 3
Sent to the L channel of the Stereo bus.
MIC/LINE INPUTs 2 and 4
Sent to the R channel of the Stereo bus.
—Owner's Manual
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE TAPE TAPE TAPE
LINE LINE LINE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
STEREO INPUT
5 6 7 8
L R L R 1
2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
+
–
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
6
Note: You can also mix the STEREO INPUT signals
for mixdown. In this case, signals at STEREO INPUT
5L/7L are sent to the L channel, and signals at
STEREO INPUT 6R/8R are sent to the R channel.
)",
3
Set the monitor select switch to "STEREO".
4
Set the [METER SELECT] switch to "STEREO".
5
Play the sound sources connected to MIC/
LINE INPUTS 1 and 2, and adjust the input
levels with the CUE controls on Input
Channels 1 and 2.
When the [INPUT-FLIP] switch is set to "TAPE (
use the corresponding CUE controls to adjust the level
of the signals input at MIC/LINE INPUTs.
+6
POWER
+3
0
–5
–10
3 4
METER SELECT
4
4 4TR
OFF STEREO
R
3
FF STOP PAUSE
)",