EINHELL CE-JS 18/1 Originalbetriebsanleitung Seite 19

plied connector (Fig. 2d / Item 14) if neces-
sary. The maximum power consumption must
not exceed 3.5A.
2. Press the ON/OFF button (Fig. 1/Item 5).
7.3 Operating 12 V d.c. devices
1. Connect a suitable connection cable to the 12
V d.c. outlet (Fig. 1 / Item 6) on the jump start
power bank and then to the 12 V d.c. device.
The maximum power consumption must not
exceed 10 A.
2. Press the ON/OFF button (Fig. 1/Item 5).
8. Jump starting for the vehicle
The 12 V jump starting function provides welcome
help with starting diffi culties due to too little batte-
ry capacity.
Warning! Only the jump start cable is allowed
to be connected during jump starting. Any power
supply to a connected device, e.g. via the USB
port, must be disconnected fi rst.
•
Consult the vehicle's operating manual for
information about jump starting. Non-obser-
vance can lead to damage to the vehicle.
•
Switch off all power consumers on the vehicle
(headlights, radio, ...). Never try to start a ve-
hicle without a connected starter battery.
•
Make sure that the connector on the jump
start cable is securely connected to the de-
vice socket. If the connection is loose during
jump starting, the connector could melt as a
result of the high current.
•
The poles on the vehicle battery must be
clean and the clamps of the jump start cable
must be securely attached to the battery po-
les.
•
Warning! Do not connect together the
clamps of the jump start cable when the
"Boost" button is pressed or while jump
starting is in progress – this will lead to short-
circuiting with sparking, to risk of explosion
and to the destruction of the equipment..
Check that at least 3 LED of the battery capacity
indicator are lit. The equipment temperature must
be within the range of + 5 °C - + 40°C and the am-
bient temperature during jump starting within the
range of – 15°C - + 40°C. Use only the supplied
jump start cable (Fig. 2c).
Anl_CE_JS_18_1_SPK9.indb 19 Anl_CE_JS_18_1_SPK9.indb 19
GB
1. Fig. 5: Pull open the cover on the jump start
cable connection (Fig. 1 / Item 1), push the
cover underneath it to the side and plug the
jump start cable into the equipment.
2. Fig. 5a: Connect the red cable to the positive
pole on the car's battery and the black cable
to the negative pole on the car's battery. Make
sure that the clamps are secure. In addition,
make sure that the jump start power bank is
tucked away securely in the engine bay and
will not be able to fall as a result of vibrations
during the jump start operation. The jump
start power bank must not be allowed to
come within the range of moving parts. The
following points 3. – 6. describe the status sig-
nals of the jump start cable. Please follow the
instructions.
3. Fig. 5a: The "Correct" LED on the jump
start cable lights up green. All the existing
connections are OK and the vehicle can be
started within 30 seconds.
4 Fig. 5b: The "Correct" LED on the jump
start cable fl ashes green. All the existing
connections are OK, but the car battery char-
ge status is very low. Press the "Boost" button
on the jump start cable and wait until the
"Correct" LED lights up green continuously.
Start the vehicle within 30 seconds.
Be particularly careful because pressing the
"Boost" button has the eff ect of overriding the
safety devices integrated in the jump start
power bank
5. Fig. 5c: The red LED on the jump start
cable lights up and an acoustic warning
signal sounds. The clamps of the jump
start cable are wrongly connected to the car
battery, i.e. with reverse polarity. Remove the
clamps and connect them to the car battery
again but with the correct polarity and in ac-
cordance with the previous instructions.
6. Fig. 5d: No LED lights up on the jump start
cable, nor is there an acoustic warning
signal. Check all the connections, especially
that the clamps are connected to the car bat-
tery with the correct polarity. If all the connec-
tions are OK, the cause is probably a defecti-
ve car battery. Press the "Boost" button on the
jump start cable and wait until the "Correct"
LED lights up green continuously. Start the
vehicle within 30 seconds.
Be particularly careful, because pressing the
"Boost" button has the eff ect of overriding the
safety devices integrated in the jump start
power bank. Replace the defective car battery
as soon as possible.
- 19 -
08.02.2021 10:28:54 08.02.2021 10:28:54