Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Wall mount
1 Casing, white, PVC
2 tap, 3/4'', with a water pressure be-
tween 2 and 6 bar
Find an installation site close to a tap
(see illustration).
The tap must have a water pressure be-
tween 2 and 6 bar
Hold the casing against the wall so that
its top edge is aligned at 1,500 mm.
Mark all three borings on the wall and
drill as deep as the dowels into the wall
with a 10 mm diameter stone drill.
Insert the wall dowels into the wall and
attach the casing to the wall using the
three stainless steel fastening screws
diam. 8x40.
Assembly
Water inlet connection
Unscrew the quick coupling from the
ball tap and connect it to the open hose
end of the black connecting hose.
Insert the 3/4'' seal ring with the sieve
into the quick coupling and screw the
quick coupling onto the ball tap.
Note
Prior to screwing the quick coupling to the
ball tap, make sure that the seal ring with
the sieve has been inserted.
Screw the counter piece of the quick
coupling with the 3/4" seal onto the wa-
ter tap.
Stick the connecting hose with the quick
coupling onto the counter piece at the
water tap.
Note
Do not turn on the tap yet!
Water outlet connection
Unscrew the quick coupling from the
Venturi outlet and connect it to the open
hose end of the fill hose.
Insert the blue Venturi nozzle into the
nozzle intake.
Insert the 3/4'' seal ring with the quick
coupling and screw the quick coupling
into the Venturi output.
Connect the detergent hose
1 EPDM connector with backflow valve
2 Dosing nozzle
Drill a 10 mm hole into the cover of the
detergent bottle.
Insert the detergent suction hose
through the hole in the cover and attach
the foot filter to the hose end on the in-
side of the cover.
Screw the cover onto the detergent bot-
tle and drop the foot filter to the bottom
of the bottle.
Note
The foot filter must stand up straight on the
bottom of the detergent bottle.
Insert the respective dosing nozzle into
the EPDM lock.
Note
The respective dosing volumes of the indi-
vidual dosing nozzles can be taken from the
"dosing table".
Slide the detergent suction hose onto
the EPDM connector.
If the detergent suction hose is too long,
it can be shortened as needed.
Note
When shortening the detergent suction
hose, make sure that the foot filter is still
standing straight up on the bottom of the
detergent bottle.
Operations
Make sure that all hose connections are
connected.
Make sure a detergent bottle is connect-
ed and that a sufficient amount of deter-
gent is present in the bottle.
The ball tap must be set to "OFF".
Make sure the correct dosing nozzle is
installed for the desired mixing ratio.
Note
The respective dosing volumes of the indi-
vidual dosing nozzles can be taken from the
"dosing table".
Insert the fill hose into the fill opening of
the floor detergent tank to be filled.
With floor cleaners with fill system, the
quick lock of the fill hose can be con-
nected to the filling system.
Open tap.
Set the ball tap to "ON".
Note
With the first use or while changing the dos-
ing nozzle, there will be air in the detergent
hose.
An optimal mixing ratio is reached, if the
tank of the floor cleaner is filled after the de-
tergent hose is completely filled with deter-
gent.
The tank of the floor cleaner is filled with
water and the desired mixture of deter-
gent.
After the fill procedure, close the tap.
Set the ball tap to "OFF" and wait a brief
moment until the fill hose has been
drained.
Remove the fill hose from the tank or
disconnect it from the fill system and coil
it onto the hose storage at the top of the
casing.
Replacing the dosing nozzles
The use of different detergents or different
types of surfaces to be cleaned require dif-
ferent mixing ratios of water and detergent.
In order to achieve different mixing ratios,
the dosing nozzles can be replaced as fol-
lows.
Set the ball tap to "OFF".
Pull the detergent hose off the EPDM
connector.
Pull the dosingn nozzle off the EPDM
connector.
Insert the respective dosing nozzle with
the desired mixing ratio into the EPDM
connector.
Reattach the detergent hose to the
EPDM connector.
7
English
Werbung
