Präzisionswaagen
Inhaltsverzeichnis
-
-
-
-
-
-
Housing's Bottom - Gehäuseunterteil
8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Twin Reference Weight Device - Zwillings-Referenzgewichts-Modul
24
-
Main Board - Hauptprint
25
-
Connector Board - Steckerprint
25
-
Display Board VFD - Anzeigeprint VFD
26
-
Power Adapter - Netzadapter
27
-
Power Adapter IP65 - Netzadapter IP65
27
-
-
Before Getting Started
28
-
About Overhauling a Weighing Cell
28
-
About These Instructions
28
-
-
-
-
-
Opening the IP65 Balance
31
-
Removing the Weighing Cell from the Housing's Bottom
32
-
Dismantling the Weighing Cell
33
-
-
Removing the 2 Flexure Holders
33
-
-
Removing the Support Piece
33
-
Removing the Balance Arm
34
-
Exchanging the Horizontal Flexures
35
-
Removing the Old Horizontal Flexures
35
-
Installing New Horizontal Flexures
35
-
-
Cleaning the Magnet Pot
36
-
-
Checking the Cleanliness Again
36
-
Assembling the Weighing Cell
37
-
Assembling the Balance Arm
37
-
Assembling the Coil, the Magnet Cover and the Transport Safety Device
37
-
Assembling the Floating Sensor and the Stopper
38
-
Assembling New Vertical Flexures
39
-
Assembling the Support Piece and the Inner Cone
39
-
Assembling the Flexure Holders
40
-
Assembling a New Coupling
41
-
Dismantling the Assembly Jigs
41
-
Installing the Weighing Cell into the Housing's Bottom
42
-
-
Before Getting Started
43
-
Table of Specifications
43
-
-
Setting the Balance to the Factory Mode (the Balance Is Open)
43
-
Adjusting the Symmetry
44
-
-
Adjusting the Corner Load
45
-
Determining the Corner Load Values
45
-
Adjusting the Corner Load (Group M/C/D)
46
-
Adjusting the Corner Load (Group A)
47
-
Checking the Lowering Process of the Internal Reference Weights (SCS Only)
50
-
Checking the Lowering Process of the Internal Reference Weights (10-Key Version Only)
50
-
Checking the Lowering Process of the Internal Reference Weights (5-Key Version Only)
50
-
-
Setting the Balance to the Service Mode (the Balance Is Closed)
52
-
Setting the Balance to the Service Mode (10-Key Version Only)
52
-
Setting the Balance to the Service Mode (5-Key Version Only)
52
-
Adjusting the Linearity
53
-
Adjusting the Linearity (10-Key Version Only)
53
-
Adjusting the Linearity (5-Key Version Only)
53
-
Checking the Repeatability
54
-
Checking the Repeatability (with SCS)
54
-
Checking the Repeatability (Without SCS)
54
-
Checking the Linearity
54
-
Checking the Corner Load
55
-
Adjusting the S-Correction
56
-
-
Calculating the S-Correction Factors
56
-
Entering the S-Correction Factors (10-Key Version Only)
56
-
Entering the S-Correction Factors (5-Key Version Only)
57
-
Adjusting the Internal Reference Weight (SCS Only)
57
-
-
Operating Errors; Error Disappears by Correct Use or Application
58
-
Fatal Errors; Balance Stays Still, Error Remediable in Service Mode
58
-
Hardware Errors; Balance Stays Still
58
-
Discussion with the Manufacturer
59
-
