Just Power on BRIEF INTRODUCTION D300S created by BLUETTI Tech Team to allow your EP500/Pro, AC300 to have a chance to connect with Roof/Rigid panels for 2400W Max. Solar charging, especially users who already have installed rigid solar panels and PV grid-connected...
4.7 in 8.5 in Output Port: connect to power the power station. Main Switch of D300S: please turn OFF during installation. NO1. MPPT(PV1 indicates DC1,Connect with your solar panels) NO2. MPPT(PV2 indicates DC2,Connect with your solar panels) Expansion Port: For future updating via 485 communication port.
INSTALLATION Step1. Please turn OFF the switch. The Main Switch of D300S is kept in the OFF state to ensure safety during installation. Step2. For EP500Pro/AC300, set DC1/DC2 Input Source to Others, and set PV Parallel Enable to OFF. (Mainpage - Settings)
Seite 7
BLUETTI Step3. The roof solar panels are connected to D300S as shown in the figure. Please make sure that one set of solar panels is connected to PV1, and the other set of solar panels is connected to PV2. Be careful not to mix them.
Seite 8
Just Power on Step4. Connect EP500Pro with D300S with DC Output Cable(Included). a.DC Output Cable to EP500Pro c.DC2 poles to PV2 poles b.DC1 poles to PV1 poles d.DC Output Cable to D300S - 05 -...
BLUETTI Step5. Turn the main switch from OFF to ON to activate the solar charging system. TECHNICAL SPECIFICATIONS List Min. Rated Max. Note DC output Power of Output 3000W Voltage 115V 135V Current Short-circuit Protection Supported PV input Power of Input...
Please ensure proper ventilation while in use, inadequate ventilation may cause permanent damage to the equipment. Do not place anything on the top of D300S, please install it where people cannot touch it. DO NOT move the unit while operating as vibrations and sudden impacts may lead to poor connections to the hardware inside.
BLUETTI shall not be liable for any damages caused by operating the product not in accordance with the method of use in the instruction manual. D300S is not suitable for the use on the relevant equipment or machines involving: Personal safety, such as atomic energy devices, Hi-Fi player, emergency medical devices, etc., or any equipment or machines that require extremely highly...
Seite 12
Company: POWEROAK GmbH Address: Lindwurmstr. 114, 80337 München Germany Mail: logi@bluetti.de Company: POWEROAK ENERGY UK CO.,LTD Address: Unit 2 NorthGate, Bolsover Business Park, Woodhouse Lane Chesterfield England, S44 6BD Mail:poweroak.eu@bluetti.com...
Seite 13
Studieren Sie dieses Handbuch vor Gebrauch und beachten Sie die darin enthaltenen Hinweise. Bewahren Sie dieses Handbuch zum späteren Nachschlagen auf.
Seite 14
BENUTZERHANDBUCH Studieren Sie dieses Handbuch vor Gebrauch und beachten Sie die darin enthaltenen Hinweise. Bewahren Sie dieses Handbuch zum späteren Nachschlagen auf.
Just Power on KURZE EINLEITUNG Das D300S von BLUETTI soll eine Verbindung zwischen EP500/Pro, AC300 und Dach-/Starrpaneelen mit max. 2400 W für das Laden von Solarstrom ermöglichen. Davon profitieren vor allem Anwender, die bereits starre Solarpaneele und netzgekoppelte PV-Wechselrichter installiert haben und bei denen die Leerlaufspannung der Solaranlage den Eingangsgrenzwert der EP500/Pro, AC300 überschreitet (140V/150V).
216 mm Ausgang: zum Versorgen der Powerstation mit Strom anschließen. Hauptschalter D300S: während der Installation in der Stellung OFF lassen. NR 1. MPPT (PV1 steht für DC1, an Solarpaneele anschließen) NR 2. MPPT (PV2 steht für DC2, an Solarpaneele anschließen) Erweiterungsanschluss: Für zukünftige Aktualisierungen über die...
INSTALLATION Schritt 1. Drehen Sie den Schalter in die Stellung OFF (AUS). Der Hauptschalter des D300S bleibt in der Stellung AUS, damit die Sicherheit während des Installationsvorgangs gewährleistet ist. Schritt 2. EP500Pro/AC300: Konfigurieren Sie „DC1/DC2 Input Source“ auf dem Bildschirm als „Others“...
Seite 19
BLUETTI Schritt 3. Die Dachsolarpaneele werden wie in der Abbildung gezeigt an das D300S angeschlossen. Vergewissern Sie sich, dass eine Gruppe von Solarmodulen an PV1 und die andere Gruppe von Solarmodulen an PV2 angeschlossen ist. Achten Sie darauf, sie nicht zu vermischen.
Seite 20
Just Power on Schritt 4. Schließen Sie die EP500Pro über ein DC-Ausgangskabel (im Lieferumfang enthalten) an das D300S an. a. DC-Ausgangskabel an EP500Pro c. DC2-Pole an PV2-Pole b. DC1-Pole an PV1-Pole d. DC-Ausgangskabel an D300S - 17 -...
BLUETTI Schritt 5. Drehen Sie den Hauptschalter von OFF (AUS) nach ON (EIN), um das Solarladesystem zu aktivieren. TECHNISCHE DATEN Pos. Min. Nennwert Max. Anmerkung DC-Ausgang Ausgangsleistung 3000 W Spannung 65 V 115 V 135 V Strom 26 A Kurzschlussschutz Unterstützt...
Achten Sie während des Gebrauchs auf ausreichende Belüftung, da eine unzureichende Belüftung zu dauerhaften Schäden am Gerät führen kann. Legen Sie keine Gegenstände auf dem D300S ab und stellen Sie das Gerät so auf, dass es von niemandem berührt werden kann.
BLUETTI haftet nicht für Schäden, die sich daraus ergeben, dass das Produkt nicht so genutzt wird, wie es die Betriebsanleitung vorsieht. Das D300S eignet sich nicht für die Verwendung mit folgenden Geräten oder Apparaturen: Nukleartechnik, Hi-Fi-Player, medizinische Notfallgeräte etc. sowie alle Geräte und Apparaturen, für die es überaus funktionssicherer Stromquellen...
Seite 24
Unternehmen: POWEROAK GmbH Anschrift: Lindwurmstr. 114, 80337 München Deutschland E-Mail: logi@bluetti.de Unternehmen: POWEROAK ENERGY UK CO.,LTD Anschrift: Unit 2 NorthGate, Bolsover Business Park, Woodhouse Lane Chesterfield England, S44 6BD E-Mail: poweroak.eu@bluetti.com...