Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8000-333B/W Tablet Stand for GENELEC 8x3x / 4x3x / G Three
Safety instructions
- Only for GENELEC 8x3x / 4x3x / G Three.
- Check the strength of the screw
-
connections at regular intervals.
- Use only on suitable, i.e. level and
-
load-bearing surfaces.
- The four device feet made of plasti-
-
cizer-free PUR decouple the monitor
-
and protect the base from scratches.
Instructions
1. COMPONENTS
a adaptor plate
b pedestal cpl., with
b.1 device feet, transparent (4x)
b.2 bearing bolts (2x)
b.3 adjusting screw M8 x 33 mm
Accessory bag (6-23275-1-00):
c 4x pan head screws M6 x 12 mm (2x)
d allen wrench SW4
2. MOUNTING
2.a First of all, it must be clarified whether the
2.a
monitor is to be mounted horizontally or
2.a
vertically on the table stand (see chapter 3.
2.a
DIRECTION). This determines which hole
2.a
pattern of the adapter plate a is screwed to
2.a
the back of the monitor.
2.b Bolt together the monitor with the adaptor
2.b
plate a. Use panhead screws M6 x 12 mm c
2.b
and the allen wrench d.
2.b
Tightening torque: ~8Nm.
2.c Mount monitor by hooking the adaptor plate
2.c
into both bearing bolts b.2.
2.d Now turn back the adjusting screw M8 x 33 mm
2.d
b.2, which was initially screwed in completely,
2.d
as far as desired. It is used for the stepless
2.d
adjustment of the beam angle (see chap. 4.).
3./4. MONITOR - SETTINGS
- Illustration of models GENELEC 8330 & 8331
- standard position for best radiation behavior
-
(see "Acoustic Center" = Ac. Ce.)
3. DIRECTION
3.a HORIZONTAL monitor
3.a.1 Centre mounting: Screw connection LEFT
3.a.2 Centre mounting: Screw connection RIGHT
3.a.3 Off-center mounting: UNAUTHORIZED!
3.a.4 Height of the acoustic center: 279 mm
3.b VERTICAL monitor
3.b.1 3-way monitor GENELEC 8331 height of
3.b.1
acoustic center: 298 mm
3.b.2 3.b.2 Standard position for classic 2-way
3.b.2
monitors; here GENELEC 8330 height of
3.b.2
the acoustic center: 335 mm
4. INCLINATION
4.a HORIZONTAL installed monitor:
4.a
Adjustment range: - 7.5° to + 20°
4.b VERTICAL installed monitor:
4.b
Adjustment range: - 9° to + 20°
4.c For the adjustment of the inclination angle you
4.b
have to turn the adjusting screw M8 b.1.
4.d NOTE: First raise the monitor slightly, then
4.c
turn the adjusting screw b.1 and now lean back
4.c
the monitor gently.
4.c
This approach conserves the thread as well
4.c
as the surface of the adaptor plate a.
GENELEC Oy
Olvitie 5, Fin-74100 Iisalmi, www.genelec.com
23275-022-56/66 Rev.02 03-80-928-00 12/22
1. COMPONENTS
2. MOUNTING
2.b 2 x
2.b
M6 x 12 mm
Mounting
example
3. DIRECTION - Used holes in the adapter plate
3.a HORIZONTAL
← Screwing correctly →
3.a.1 LEFT
centered
4. INCLINATION
4.a
Angle
Acoustic Center
4.d
raise the
monitor slightly
(before adjustment)
2.c Hook in the adaptor plate
3.a.3 UNAUTHORIZED!
3.a.3
3.a.2 RIGHT
centered
3.a.4
3.b VERTICAL
4.a + 20°
4.b + 20°
4.c
adjust-
ment
4.a - 7,5°
4.b - 9°
2.d Insert adjusting
2.d
screw
Screwing wrong
Off-center
Ac.
Ce.
Ac.
Ce.
Werbung
