Product Specifications - SUNLU FilaDryer S2 Bedienungsanleitung

TM
FilaDryer S2
3D PRINTING-MATE
Drying while printing to improve your 3D model.
EN / DE / FR / IT / ES / JP
Zhuhai Sunlu Industrial Co. , Ltd.
Website: www.sunlu.com
Business Coopera�on: sales@sunlu.com
A�er-sales Service: support@sunlu.com
Address: 38, Yong�an Road, Fuxi Industrial Zone, Xiangzhou District,
Zhuhai Guangdong, China.
M A D E I N C H I N A
EN
Note: Read this document before using the
filament dryer
· Do not place the product where children can reach.
· Pay a�en�on to electrical safety during opera�on. Do not use this
product near water, such as in the bathroom, bathtub, wash basin and
other places where water is easily accessible.
· Only use the original power adapter or a fully cer�fied 24V/2A power
adapter.
· Switch off the power supply when not using this product to avoid
sudden fire.
· Place the two rollers in the box before opera�ng the dryer.
· Confirm filament �ghtly wound to the roll before using this product to
prevent it from falling onto the heat sink, resul�ng in high temperature
deforma�on of the filament.
· When drying filament, do not place the products on temperature
sensi�ve objects.
· Do not touch the heaters in the oven when drying filament to avoid
burns.
· The upper lid of the drying oven should be covered when drying
consumables to avoid heat loss.
· In order to ensure the drying effect, do not open the drying box at will
during opera�on.
· If there is a fault with the product , disconnect the power adapter from
the filament dryer and the electrical socket then contact the a�er-sales
support team.
Product specifications:
Product size
265 (L) X 274 (W) X 118 (H) mm
Maximum capacity
φ210 * 85 (H) mm
Net weight
1190g (including power adapter)
a) Environment temperature: 20 ℃ ~ 35 ℃
Working environment
b) Rela�ve humidity: ≤ 90%
Temperature se�ng range
35 ℃ ~ 70 ℃
a) Input specifica�ons: AC 100V ~ 240V, 50 / 60Hz
Power adapter specifica�ons
b) Output specifica�ons: DC: 24V ± 1.2V, 2A
Standby power
0.05W
Maximum working current
1.9A
Maximum working power
48W
LCD display screen
4.6-inch LCD display
Suitable for filament diameters
1.75mm/2.85mm
Product function diagram:
Display control panel
Schematic Diagram of the Content Displayed
on the LCD:
Cursor Column
Touch Bu�on
Hea�ng Film Port
Operation Guide:
1. Power On
Plug the power adapter a�ached to this product into the power supply,
and then connect the power cord to the DC power socket of the dryer.
The dryer is in standby without hea�ng state by default a�er the power
is connected, and the screen displays"
2. Filament Loading
Place the filament in the dryer, pull the thread out of the outlet and close
the lid �ghtly. (Note: Please make sure that the consumables are in a
�ghtly wound state).
3. Turn On the Dryer
Double-click the "
se�ngs (Temperature: 50°C, drying �me: 6 hours, material: PLA, LED:
OFF).
4. Personalized Se�ngs
A.This product can change the temperature unit.
Click the " ", when the cursor on the le� side of the PV flashes, click
SET
" " or" " , you can switch between Fahrenheit and Temperature
Celsius.
B.This product can increase or decrease the temperature according to
personal se�ngs (temperature se�ng range: 35℃~70℃).
Click the "
SET
" " or " ", , the temperature can be increased or decreased. A�er
LED light circle
3 seconds of stopping the opera�on, the dryer will automa�cally save the
set temperature.
In addi�on, you can click"
DC power socket (24V 2A)
Measured Temperature
Measured Humidity
PV:
C F %
RH Temperature Se�ng
SV:
C F
Drying Time
Time:
Material:
Selec�on of Drying Materials
LED:
OFF ON RUN
ON
SET Working Mode of LED
OFF
www.sunlu.com
DC24V 2A Port
Thermistor Port
".
ON
OFF
ON ",the dryer will work according to the default
OFF
", when the cursor on the le� side of the SV flashes, click
"or " "directly without the cursor flashing.