Safety Instructions; Commissioning; Operating The Hand Switch With Memory Function; Initialization Procedure - Wiesner hager foxx eRK Montage- Und Bedienungsanleitung

3. Safety instructions

Important note: you must read the user manual carefully before installing or operating the control unit!
✓ Do not open the control unit under any circumstances, because there is a danger of electric shock.
✓ The control unit has not been constructed for continuous operation. Changing the table height without interruption
must not exceed the duty cycle indicated on the nameplate!
✓ The control unit may only be operated with mains voltage as specified on the nameplate.
✓ Only use an original power cord and check that it is not damaged. It is prohibited to operate the control unit if the
power cord is damaged!
✓ You must unplug the power cord before connecting and disconnecting handswitches.
✓ Damaged power cords must be replaced by the manufacturer, its customer service or a similarly qualified person.
✓ Clean the control unit with a dry or slightly moist cloth only. Always unplug the power cord before cleaning!
✓ To prevent damage of the unit, it is not allowed to connect self-constructed products to motor controls.
✓ In case of a malfunction, please unplug the unit immediately.
✓ Protect the control unit from moisture, water drops or splashes.
✓ It is forbidden to modify or make any changes to the control unit, the controls themselves or handswitches.
✓ Do not operate the control unit in a potentially explosive environment.
✓ This device is not designed for use by children or individuals with limited physical, sensory or mental abilities or
with a lack of experience and/or lack of expertise, unless they are supervised or have received instructions on how
to use the control unit.
✓ There is a risk of contusion when changing the desktop position. Therefore you have to ensure that no people or
objects are located in the area of risk or can reach into it.
✓ In case of a malfunction, the desktop may move slightly before the safety cut-out is triggered. Please note that
there is a potential risk of crushing!

4. Commissioning

Caution: the power cord must be unplugged while the control unit is being commissioned.
Commissioning procedure.
✓ Connect drives and hand set
✓ Connect mains supply
✓ Reset at first use
24 english

5. Operating the hand switch with memory function

5.1 Initialization procedure

1. Press and hold & simultaneously for more
than 3 seconds. The desktop begins to move
down at half speed of normal operation.
2. Keep pressing & . The desktop moves
down to the lowest position and rebounds
2-5 mm, then stops.
3. Release & together. Initialization is
completed.
The initialization procedure must be comple-
ted before the table is first used after being
installed, in the event of a power failure lasting
more than 96 hours or if parts have been re-
placed.

5.2 Verify the display switch data to table height

1. Set the table at random height. We recommend
at the bottom position. Measure the actual table
height and write down the number in inches or
in centimeters.
2. Press and hold button S, then press and hold
for about 3 seconds. The first number starts
flashing on the display.
3. Release the buttons, then press or to
change the first number. The first number can be
increased or decreased to the first number you
measured.
4. Press button S. The second number starts
flashing on the screen.
Check the switch display format in inches or in centimeters (chapter 5.6) and toggle to the unit you
like and match to the actual measurement. In inch format, the minimum adjustable height is 0.5 inches,
while in centimeter format it is 1 centimeter.

5. 3 Upward and downward desktop movement

1. Press and hold until the required desktop
height is reached. Desktop moves upward until
you release the key or the maximum height is
reached.
2. Press and hold until the required desktop
height is reached. Desktop moves downward
until you release the key or the minimum height
is reached.
1
2
Display 3 S
upwards downwards
5. Press or to change the number. The second
number can be increased or decreased to the
second number you measured.
6. Press button S. The third number starts flashing
on the display
7. Press or to change the number. The third
number can be increased or decreased to the
third number you measured.
8. Press button S. Completed.

5. 4 Saving desktop positions

1. Press and hold or until the required
desktop height is reached, then release. Move
the desktop to the position you want the
table surface to be.
Press button S, then click button 1, 2 3
2. or
within next 3 seconds. Position 1, 2 or 3 is
saved.
english 25
EN