Mounting And Wiring; Technical Information - Steute Rf Lds Spot-St-Net Montage- Und Anschlussanleitung

RF LDS SPOT-ST-NET / RF LDS SPOT-ST/BU-NET /
//
RF LDS ZONE-ST-NET / RF LDS ZONE-ST/BU-NET
Montage- und Anschlussanleitung / Funk-Laserentfernungsmesser
Mounting and wiring instructions / Wireless laser distance meter
Instructions de montage et de câblage / Télémètre laser sans fil
Istruzioni di montaggio e collegamento / Distanziometro laser wireless
Instruções de montagem e instalação / Medidor de distância a laser sem fio
Инструкция по монтажу и подключению / Лазерный радио-дальномер
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer. In case
of doubt, the German language version of these instructions shall
prevail.
Scope of delivery
Device, mounting and wiring instructions, carton.
Intended use
The device is designed for connection to the RF 96 BU SW868/SW915/
SW917/SW922-NET-LDS; the material no. depends on the frequen-
cy variant (on request). Up to four devices can be connected to an
RF 96 BU SW...-NET-LDS in total. Please use a 4-pole connecting
cable.

Mounting and wiring

With the help of the flange attached to the enclosure, the device can be
mounted on an even surface or a pipe. A bracket with a stand, Material
no. 1390766, offers additional flexible mounting options.
Connect the device as described for the initial operation in the
RF 96 BU SW868/SW915/SW917/SW922-NET-LDS mounting and
wiring instructions.
Accessory:
Name
RF LDS bracket with a stand
Cable 4pin M8x1 with plug/socket
Y-Distributor M8 plug / M8 socket 0° A-cod

Technical information

The distance is determined by measuring a light impulse. The time
required for the light impulse to travel to an object and back is used
to calculate the distance based on the speed of light. This measuring
principle means that the switching point is largely independent of the
colour and material of the object. The quantity of reflected light has
no influence on the switching distance, provided that sufficient light is
reflected for the measuring process. This is the case for conventional
materials. With some porous and very low-reflecting materials, it is
possible that the full extent of the switching distance cannot be used.
Very strongly reflecting or mirroring materials can lead to deviations
in the switching distance. In order to save energy when using a bat-
tery-driven system and thus to increase battery life, distance calcula-
tions are clocked. The interval between the individual measurements,
as well as the switching distance, are stipulated by RF 96 BU SW...-
NET-LDS and configured.
Safety
Do not use the device in connection with other devices whose direct
or indirect purpose is to ensure life or health, or whose operation may
pose a threat to humans, animals or material assets. Do not look at
ray with optical instruments.
N.B.
Subject to technical modifications. Reconstruction and alterations to
the device are not allowed. The described products were developed in
order to assume safety functions as part of an entire plant or machine.
It is the responsibility of the manufacturer of a plant or machine to
guarantee the correct general function.
Maintenance and cleaning
.steute recommends routine maintenance as follows:
1. Remove all dirt particles: Clean enclosure on the outside only.
Clean device in accordance with IP protection class. Clean with
a soft cloth and water or a mild detergent. Do not clean using
compressed air.
N.B.: PMMA protective screen must not be cleaned with alcohol!
2. Replace damaged parts.
3. Test the function.
Disposal
- Observe national, local and legal regulations concerning disposal.
- Recycle each material separately.
Material No.
ESD
1390766
Ensure adequate ESD protection for all work that requires opening
the unit.
1254189
1314363
2 / 16