Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Floor stand for vacuum cleaner
Item no. 2388666
Intended use
This product is a floor stand for vacuum cleaners. It is compatible with the Dyson models V6,
V7, V8, V10, V11, V12 and V15.
Any use other than that described above, or using the product with other vacuum cleaner
models may damage the product or the vacuum cleaner or cause other risks such as damage
to nearby furniture, personal injury, etc.
This product complies with statutory, national and European regulations. All company and prod-
uct names contained herein are trademarks of their respective owners. All rights reserved.
Delivery content
• 1x Base plate (A)
• 1x Stand pipe
• 1x Mounting plate (C)
• 2x Accessory holders (D)
• 4x M5 x 8 screws (E)
• 2x M5 x 16 screws (F)
• 3 x M5 x 20 screws (G)
• 2x M5 nuts (H)
• 1x 3 mm hex key (I)
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Description of symbols
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and tips on how to use the product.
Safety information
Read the operating instructions carefully and observe in particular the safety
instructions. If you do not follow the safety information and information on
proper handling in these operating instructions, we will assume no liability
for any resulting personal injury or damage to property. Such cases will also
invalidate the warranty/guarantee.
• T he vacuum cleaner floor stand contains small parts and is not a toy. Keep the
product out of the reach of children.
• Do not leave packaging material lying around carelessly. It may become
a dangerous plaything for children.
• The product may only be used for the specified vacuum cleaner models. Use in
conjunction with other and/or heavier products may cause instability and injury.
• The product may only be used indoors. Protect it from moisture and humidity.
• Exercise caution when assembling the product and follow these assembly
instructions carefully. The product may have sharp edges. There is a risk of injury!
• Only use suitable tools to assemble the product.
• The supporting surface must be able to support the weight of the vacuum cleaner
floor stand and the vacuum cleaner, including all accessories attached to it.
• Make sure that the supporting surface is non-slip, horizontal and level.
• Only use the supplied mounting accessories to assemble the product.
• For safety reasons, any unauthorised conversion and/or modification of the
product is not permitted.
• D o not hold onto the vacuum cleaner floor stand or use it to support yourself.
• Do not attach any other objects to the vacuum cleaner floor stand other than the
vacuum cleaner and its accessories.
• Do not place the product under any mechanical stress.
• If you are not sure how to assemble or use the product, or if questions arise which
are not covered by the operating instructions, contact our technical support or
another specialist.
Assembly
Please refer to the illustrations on the last page.
a) Figure 1
• Attach the stand pipe (B) to the base plate (A).
• To do this, use the screws (G) and the hex key (I).
b) Figure 2
• Attach the mounting plate (C) to the head of the stand pipe (B).
• To do this, use the screws (E) and the hex key (I).
• Guide the connecting cable on your vacuum cleaner charging holder through the opening in
the mounting plate (C) as shown.
• Attach the charging holder to the mounting plate (C).
• Use the screws (F), nuts (H) and a suitable screwdriver.
c) Figure 3
• Attach the accessory holders (D) to the stand pipe (B).
• Place the connecting cable on the charging holder into the groove on the stand pipe (B) as
shown in the illustration.
Maintenance and cleaning
Never use aggressive detergents, rubbing alcohol, organic solvents or other
chemical solutions, as these may damage the product or prevent it from functioning
properly.
• Clean the vacuum cleaner floor stand with a dry or slightly damp cloth, and then wipe it dry
if necessary.
• Check the product regularly to ensure that it is stable and securely in place (every 3 months).
• In addition, check all screw connections and tighten them if necessary.
Technical data
Dimensions . ..........................................298 x 298 x 1266 mm
Weight ..................................................3.94 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
2388666_v1_1021_02_VTP_m_en
Werbung
