Dane Techniczne Model Napięcie Częstotliwość Klasa 2 MalTec Grzejnik PTC Osylacyjny 2000W 220-240V 50/60Hz HighLine2200 +Pilot Instrukcja bezpieczeństwa 1. Podłącz grzejnik do gniazdka 220-240V ~ 50 / 60Hz, sprawdź gniazdko podczas używania i wybierz gniazdko 250V ~ 10A lub wyższe i sprawdź, czy gniazdko i wtyczka są...
Opis produktu Grzejnik PTC Oscylacyjny 1. Włącz zasilanie, wyświetlacz LED pokazuje HighLine2200 +Pilot temperaturę otoczenia, urządzenie jest w trybie czuwania; patrz rysunek 2.1 2. Naciśnij w następujący sposób: ON (działa tylko wentylator), OFF (wentylator działa przez 30 sekund po wyłączeniu urządzenia (po nagrzaniu)) Patrz rysunek 3.1...
Seite 4
WENTYLATORA, patrz rysunek 4.1-.4.2 4. Naciśnij aby ustawić timer, 1h, 2h, 3h ..12h, patrz rysunek 5.1-5.3 5. Naciśnij następnie ustaw temperaturę. Zakres temperatur 15-45 , patrz rysunek 5.4-5.5 ℃ 6. Wciśnij SWING ON, SWING OFF, patrz rysunek Wyświetlacz 6.1 Jeżeli urządzenie wychyli się lub przewróci zostanie automatycznie wyłączone.
rysunek 11.6 Uwaga: wskaźnik świeci się, gdy działa odpowiednia funkcja 11.1 11.2 11.3 11.4 11.5 11.6 KONSERWACJA I CZYSZCZENIE 1. Przed czyszczeniem urządzenie należy upewnić się, że jest odłączone od zasilania i całkowicie ostygło, a następnie po wyczyszczeniu umieścić je w opakowaniu. Należy je umieścić...
Seite 6
źródła zasilania lub nieprzestrzeganie instrukcji instalacji 5. Częściowo lub całkowicie zdemontowane urządzenia Deklaracja CE Malis sp. z o.o. sp. k. Deklaruje że urządzenie MalTec Grzejnik PTC Oscylacyjny HighLine2200 +Pilot spełnia wszelkie wymogi dotyczące dyrektywy LVD 2014/35/EU, EC 2014/30/EU oraz spełnia następujące standardy:...
Seite 7
PTC Fan Heater HighLine2200 +Pilot Instruction Manual 7/19...
Rated Model Rated Power Voltage Frequency Class II HighLine2200 2000W 220-240V~ 50/60Hz Safety instruction 1. Plug the heater into a polarized 220-240V~ 50/60Hz outlet, please check the outlet when use and choice 250V~ 10A or above outlet, and check outlet and plug connection is good.
Product Diagram HighLine2200 1. Turn on the power switch, LED display shows Environment temperature, the appliance is in standby mode; see picture 2.1 2. Press “ ”as follows: ON(only Fan working), OFF(Fan keep working for 30 seconds when shutdown the appliance(after heating) );see picture 3.1...
Seite 10
3. Press “ ”, low heat, high heat, FAN working, see picture 4.1-.4.2 4. Press “ ” to set timer, 1h、2h、3h..12h, see picture 5.1-5.3 5. Press “ ” , then can set temperature. Temperature range 15-45 , ℃ see picture 5.4-5.5 Display window 6.
temperature, appliance will low heat. See picture 11.4-11.5 Set temperature is higher or equal to Environment temperature+3 , appliance will high heat. See picture 11.6 ℃ Note: The indicator lights when corresponding function is working 11.1 11.2 11.3 11.4 11.5 11.6 MAINTENANCE AND CLEANING Before cleaning the appliance ,ensure it is disconnected from the power supply and has...
Seite 12
4. Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains supply or non-compliance with the installation instructions 5. Partially or completely dismantled appliances 12/19...
Seite 13
CE declaration Malis sp. Zoo. sp. k. Declares that the device MalTec Oscillating HighLine2200 + Pilot PTC Heater meets all standards related to LVD 2014/35 / EU, EC 2014/30 / EU regulations and meets the following standards: EN 55014-1:2017 EN 55014-2:2015...
Seite 14
Heizlüfter PTC mit Oszillation HighLine2200 + Fernbedienung Bedienungsanleitung...
Technische Daten Modell Heizleistung Spannung Frequenz MalTec Heizlüfter PTC mit Klasse 2 Oszillation 2000W 220-240V 50/60Hz HighLine2200 + Fernbedienung Sicherheitshinweise 17. Schließen Sie der Heizlüfter an die Steckdose 220-240V ~ 50/60Hz an, prüfen Sie die Steckdose bei der Verwendung und wählen Sie eine Steckdose 250V ~ 10A oder höher und prüfen Sie, ob die Steckdose und der Stecker in gutem Zustand...
Erfahrung und Wissen benutzt werden, wenn sie beaufsichtigt oder bezüglich des Gebrauchs des Geräts unterwiesen wurden und die daraus resultierenden Gefahren verstehen. Kinder sollten nicht mit dem Gerät spielen. Kinder dürfen das Gerät nicht ohne Aufsicht reinigen oder warten. Produktbeschreibung 16/19...
Seite 17
Heizlüfter PTC mit Oszillation 7. Schalten Sie das Gerät ein, die LED-Display zeigt die HighLine2200 + Fernbedienung Umgebungstemperatur an, das Gerät befindet sich im Standby-Modus; siehe Abbildung 2.1 8. Drücken Sie wie folgt: ON (EIN; nur der Lüfter arbeitet), OFF (AUS; der Lüfter arbeitet für 30 Sekunden nach dem Ausschalten des Geräts (nach...
Drücken Sie „ ”,um den Timer einzustellen, 1h, 2h, 3h ..Drücken Sie“ ” “ ” und stellen Sie die Temperatur ein. Der Temperaturbereich 15-45 ℃ Zum Beispiel beträgt die Umgebungstemperatur 25 ℃ siehe Abbildung 11.1 Die eingestellte Temperatur ist gleich oder niedriger als die Umgebungstemperatur, das Gerät hört auf zu heizen.
5. Teilweise oder vollständig demontierte Geräte EU-Konformitätserklärung Malis sp. z o.o. sp. k. [GmbH & Co. KG] erklärt, dass das Gerät MalTec Heizlüfter PTC mit Oszillation HighLine2200 + Fernbedienung alle Anforderungen der Richtlinien LVD 2014/35/EU, EC 2014/30/EU und der folgenden Normen erfüllt:...