Inhaltszusammenfassung für Pauli + Sohn 3441ZN-SAG
Seite 1
ZN135 - tiefschwarz matt lackiert sliding glass surface color: door lock ZN135 - painted deep black matt Pauli + Sohn GmbH Stand: 1 1/2022 Eisenstraße 2 • 51545 Waldbröl Industriestraße 20 www.pauli.de Telefon: +49(0)22 91-92 06-0 51597 Morsbach info@pauli.de...
Seite 2
Oberfläche: ZN1 - mattverchromt surface color: ZN1 - matt chrome Die Schrauben und das Schließblech entfernen. Die Madenschrauben lösen und die Abdeckkappen abnehmen. Remove the screws and the lock plate. Loosen the grub screws and remove the cover caps.
Seite 3
Empfehlung P+S: Recommendation P+S: ISEO Schließzylinder F5 ISEO lock cylinder F5 21/21 21/21 Art.-Nr.: 3440-103MS art. no.: 3440-103MS Das Kontaktmaterial entsprechend der Glasdicke Den Schließzylinder einsetzen. Im gesperrten Zustand einstecken. muss der Nocken des Schließzylinder wie in der Abbildung stehen. Insert the contact material according to the glass Insert the lock cylinder.
Seite 4
Den Schließzylinder befestigen. Das Schloss in den Glasausschnitt postionieren. Secure the lock cylinder. Position the lock in the glass cutout.
Seite 5
Das Schloss mit den Druckschrauben am Glas Die Abdeckkappen aufstecken und mit den Maden- befestigen. schrauben klemmen Secure the lock to the glass using the clamp screws. Attach the cover caps and secure them with the grub screws (1).
Seite 6
Optional kann eine Schlossrosette aufgeklebt Das Schließblech montieren. werden. A lock collar can be bonded as an option. Attach and secure the lock plate.
Seite 7
Optional – Griffmontage: Mit einem Ø5mm-Bohrer Optional - handle mounting: Drill through the rear- durch die von hinten aufgesteckte Abdeckkappe bohren. mounted cover cap with a Ø5mm drill bit. Abdeckkappe entnehmen und auf Ø6,5mm aufbohren. Remove cover cap and drill out to Ø6.5mm. Beide Abdeckkappen entsprechend bearbeiten.
Seite 8
Optional – Griffmontage: Einen Griff nach Wahl am Optional - handle mounting: Attach a handle of your Schloss mit dem beiliegenden Montagestück choice to the lock using the enclosed mounting piece and threaded stud (2). Gewindestift befestigen. ACHTUNG: Den Gewindestift nicht zu weit in das CAUTION: Do not screw the threaded stud too far into Schloss eindrehen um die Freigängigkeit des...
Seite 9
Optional – Wandmontage Gegenkasten: Die Optional - Wall mounting lock-box: Attach the cover Abdeckkappe hinten aufstecken und mit Ø4,5mm to the rear and drill through it with a Ø4,5mm Bohrer durchbohren. Gegenkasten mit geeignetem drill bit. Secure the lock-box to the wall using suitable Befestigungsmaterial auf der Wand verschrauben.
Seite 10
-Füllstück für Wandmontage -Füllstück für Wandmontage Folgende Oberflächen 3440-52ZN 3440-52ZN ZN1 = Mattverchromt ZN5 = Glanzverchromt Glasbearbeitung iert ZN35 = schwarz matt lackiert ZN22 = Edelstahloptik Glasbearbeitung Glasbearbeitung...
Seite 12
Pauli + Sohn GmbH Stand: 1 1/2022 Eisenstraße 2 • 51545 Waldbröl Industriestraße 20 www.pauli.de Telefon: +49(0)22 91-92 06-0 51597 Morsbach info@pauli.de Telefon: +49(0)22 94-9803-0 Versionsnr.: A - Stand: Novmeber 2022 Technische Änderungen der Pauli+Sohn GmbH vorbehalten! Technical changes are reserved by Pauli+Sohn GmbH!