Herunterladen Inhalt Inhalt Diese Seite drucken

Product Overview; Ice Maker; Filling The Water Tank; Making Ice - Conrad 2377926 Bedienungsanleitung

Eiswürfelbereiter, 1,8 l
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Never pull the mains plug from the socket by pulling at the cable. Always pull it from the

mains socket using the intended grips.
Unplug the mains plug from the mains socket if you do not use the device for an extended

period.
Disconnect the mains plug from the mains socket in thunderstorms for reasons of safety.

Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put

under mechanical stress.
Avoid excessive thermal stress on the mains cable from extreme heat or cold.

Do not modify the mains cable. Otherwise, the mains cable may be damaged. A damaged

mains cable can cause a deadly electric shock.
Do not touch the mains cable if it is damaged.

– First, power down the respective mains socket (e.g. via the respective circuit breaker)
and then carefully pull the mains plug from the mains socket.
– Never use the product if the mains cable is damaged.
A damaged mains cable may only be replaced by the manufacturer, a workshop

commissioned by the manufacturer or a similarly qualified person, so as to prevent any
danger.
Ensure that cables are not pinched, kinked or damaged by sharp edges.

Always lay cables so that nobody can trip over or become entangled in them. This poses

a risk of injury.

7 Product overview

7.1 Ice maker

12
10
13
14
11
15
1 Top lid
8 Ice shovel
2 Viewing window
9 Water tank
3 Front cover
10 Infrared light-receiving
diode
4 Back housing
11 Drain plug
5 Front housing
12 Control panel
6 Evaporator
7 Ice tray
1
2
3
4
5
13 Infrared light-emitting
diode
14 Filter
15 MAX water level mark
16 Ice basket
17 Ice scoop
7.2 Control panel
1
1 ON/OFF key to start or stop the appliance.
2 SMALL indicator is selected for small ice
setting.
3 LARGE indicator is selected for large ice
setting.
4 CLEAN indicator is selected when the
appliance needs to be cleaned.
5 SELECT key for selecting SMALL,
LARGE or CLEAN in standby mode or
SMALL or LARGE when powered on.
8 Placement
Important:
6
– While moving do not turn upside down and ensure an incline angle of 0 to 45°.
– Ensure an ambient temperature of +10 to +38 °C.
7
– Keep away from heat sources such as ovens and heaters.
8
9
1. Place the ice maker on a dry, stable and level surface. Ensure an incline angle of 0 to
45°. Leave approx. 15 cm of clearance on all sides for proper ventilation.
9 Operation
Important:
Wait for min. 30 minutes (2 hours if using for the first time) after the ice maker has been
placed to allow the fluid in the compressor to settle.

9.1 Filling the water tank

1. Open the top lid and remove the ice basket.
NOTICE: Do not use hot water!
2. Fill the water tank with cold or room temperature drinking water (+10 to +25 °C) up to the
16
MAX water level mark.
3. Replace the ice basket and close the top lid.
Tip: use cold water to shorten the ice-making process.

9.2 Making ice

17
After you select an ice bullet size, the ice maker makes ice within 7-15 minutes.
Making ice
1
The drain plug at the bottom of the water tank is closed.
D
The water tank is filled up to the MAX water level mark.
D
1. Connect the mains plug to a suitable wall outlet.
The POWER indicator blinks.
Æ
2. Press the ON/OFF key to turn the ice maker on.
The POWER indicator is continously on.
Æ
3. Repeatedly press the SELECT key to select the required ice size, then release to start
the ice-making process.
The ice-making process starts.
Æ
4. Wait until the ICE FULL indicator lights up. It indicates that the ice basket is full.
5. Open the top lid and remove ice with the ice scoop.
After ice is removed, the ice-making process restarts after approx. 5 seconds.
Æ
Stop making ice
2
1. If you have enough ice, press the ON/OFF key to stop the ice-making process.
2. Wait for the POWER indicator to start blinking, then disconnect the mains plug from the
wall outlet.
3. Let the ice maker cool down to room temperature.
Running out of water
3
If the ice maker runs out of water, the ADD WATER indicator lights up and the ice-making
process stops. Take the following steps to restart:
1. Refill water.
Press the ON/OFF key to restart the ice-making process.
Important: the Ice-making process restarts automatically after 30 minutes, if you do not
restart it with the ON/OFF key.
2
3
6
7
6 POWER indicator that blinks in standby
mode and is continuously on when
powered on.
7 ADD WATER indicator lights up when
water needs to be added to the water
tank.
8 ICE FULL indicator lights up when the ice
basket is full.
4
5
8

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis