HIKVISION DS-PM1-O4L-H Bedienungsanleitung

DS-PM1-O4L-H
Wired Relay Expander
User Manual
EN 50131-1+A1+A2+A3
EN 50131-3: 2009
EN 50130-4: 2011+A1: 2014
EN 50130-5: 2011
Security Grade 2
Environment Class II
English
1 Appearance
1 Indicator
Green and orange quickly flashing
Slowly flashing light green:
alternately:
Waiting for enrollment
Enrolling
Solid orange:
Solid green: Enrolled
Enrolling failed/Fault (Disconnected)
Quickly flashing orange: Flashing green:
Alarm Find me mode
2 Installation
3 Wiring
4 Address Settings
Configure the address via DIP switch of the expander before
powering on the system. The address should be in the range
(0 to 63). The address of each expander should be unique.
The binary value shown in the diagram is 000011, which means
the decimal value is 3, so the address of the expander is 3.
Specification
Serial port 1 TTL serial port
Tamper-Proof Support(front and rear)
2×Speed-X bus, 1 uplink for control
Bus panel connection and 1 downlink for
next expander
Power supply 11 to 24 VDC, 1 A
Maximum current 153 mA@12 VDC
Power consumption
Quiescent current 70 mA@12 VDC
Output Current Maximum 500 mA
Output Voltage 9 to 12 VDC
LED Indicator 1 for power, 1 for fault
Dimension(W × H × D) 110 mm × 155 mm × 32.5 mm
Shell material Plastic
Weight 285 g
Operation temperature -10 °C to 40 °C
Operation humidity 10% to 90%
UD29250B
1
1
3
4
1 1
0 0
Lowbit Highbit
BIN=000011 Address=3
NC1 COM1 NO1 NC2 COM2 NO2
1
LOAD LOAD
+ +
- -
NC1 COM1 NO1 NC2 COM2 NO2
2
LOAD LOAD
+ +
- -
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
2
1
BIN Address BIN Address
110111 55
000000 0
111000 56
000001 1
111001 57
000010 2
111010 58
000011 3
000100 4 111011 59
000101 5 111100 60
000110 6 111101 61
000111 7 111110 62
...
111111 63
NC3 COM3 NO3 NC4 COM4 NO4
LOAD LOAD
+ +
- -
NC3 COM3 NO3 NC4 COM4 NO4
LOAD LOAD
+ +
- -
2
BUS_OUT BUS_IN
D- D+ D-
WIRED CONTROL
RELAY PANEL
EXPANDER
CONTROL
PANEL
Speed-X BUS
CONTROL
PANEL
OR
BUS_IN BUS_IN
WIRED WIRED
... ...
RELAY RELAY
EXPANDER EXPANDER
BUS_OUT BUS_OUT
... ...
Support cascade connection
Note: A jumper is required on
Termination_1 of the last Speed-X
device on the Speed-X bus.
Note: Add jumpers on all
Termination_1 from the second relay
module to the last relay module.
12VDC_IN
AUX
D+ - + - +
LOAD
DC 12V
POWER
Speed-X BUS
BUS_IN
WIRED RELAY
EXPANDER
BUS_OUT
BUS_IN
WIRED RELAY
EXPANDER
BUS_OUT
...MAX. 15...
BUS_IN
WIRED RELAY
EXPANDER
BUS_OUT