Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Radio safety device with wireless transmitter. ARPO 58: radio communication system to be used as safety device with sliding and swinging gates, rolling doors, up-and-over garage doors,
sectional doors, fast guillotine doors and road barriers. The system can consists of:
• up to 4 ARPO 58 transmitters with two inputs set by jumpers able to control either mechanical safety edges with NC clean contact or 8,2 kΩ resistive ones.
Operated by 2 x AA 1,5 V battery, 4 years battery life.
• one ARPO 58 receiver with 2 selectable outputs, either NO or NC associated to the ARPO transmitter inputs, and one x NC safety STOP output.
12/24 Vac/dc selectable power supply. Receiver distance range 100 m with aerial and 30 m without aerial.
ARPO 58 transmitter
43 mm
42
ARPO 58 transmitter
Transmitter red led
ON
Frequency dip-switch
OFF
Separated A and B inputs
ARPO 58 transmitter
for NC or 8,2 kΩ
safety edges
ADDITION OF TRANSMITTERS TO ARPO 58 RECEIVER
ATTENTION: it is important that the frequency dip-switches are set in the same way on both ARPO 58 receiver and the
transmitters associated with it. By changing these dip-switches it is possible to select the operating frequency, and manage
up to 4 installations nearby. In case more transmitters are used, each of them is to have its own combination of jumpers for
transmitter code selection, different from each other, in order to uniquely identify the transmitters associated with the
receiver. Possible combinations:
1
Select the type of safety edge to be associated with A and B inputs in
the transmitter by the dedicated jumper next to A and B terminal.
2
Set the programming dip-switches 1 and/or 2 in the ARPO 58 receiver
- dip 1 ON only to program A input of the ARPO 58 transmitter
ON
- dip 2 ON only to program B input of the ARPO 58 transmitter
1 2 3
OFF
- dip 1 and 2 ON to program both A and B inputs of the ARPO 58 transmitter
3
Press programming button in the ARPO 58 transmitters that are required to be added on to ARPO 58 receiver
4
Set to OFF ALL of the programming dip-switches in the ARPO 58 receiver
ON
1 2 3
OFF
POSSIBLE MALFUNCTIONS
Faults
Red led in ARPO 58 transmitter flashes
Four alternated beeps in ARPO 58 receiver
Continuous beep and red led with fixed light
in ARPO 58 receiver
TECHNICAL DATA
Power supply
Battery life
Frequency
Distance range
No. of transmitters to associate
Selectable frequencies
Outputs
Relays
Working temperature
Maximum consumption
Protection standard
Compatible safety edges
ARPO 58
7498
GB
Drwg. No.
To open
Cover
RADIO
Transmitter code
LINK
selection jumpers
ARPO
Programming button
Either NC or 8,2 kΩ
input jumper
Jumper fitted, input for
A
B
8,2 kΩ resistive safety
edges.
Not fitted, input for
mechanical
edges with NC clean
contact
Causes
Transmitter not associated with the ARPO 58 receiver
Transmitter to the limit of the ARPO 58 receiver distance range
Batteries almost run down
Batteries run down
Transmitter beyond ARPO 58 receiver distance range
Receiver
12/24 Vac/dc
868 MHz
100 m with aerial
30 m without aerial
4
4
2 (NA or NC) + 1 safety stop (NC)
1 A/24 Vdc
-20 °C +70 °C
66 mA
IP 53
Via Mantova, 177/A - 37053 Cerea (VR) Italy
Ph. +39 0442 330422
e-mail: info@fadini.net - www.fadini.net
Safety
edge
ARPO 58
transmitter
ARPO 58 receiver
Sounder
Frequency dip-switch
NO
Jumpers to select either
R1/R2 NO or NC outputs
Jumper for 12 Vdc power supply:
Jumper fitted, 12 Vdc supply is
possible
ARPO 58 receiver outputs
- R1: associated with transmitter A inputs
- R2: associated with transmitter B inputs
safety
- R3 - STOP: in case any transmitter signal is lost, either because of malfunctioning
of the same or run down batteries, this emergency contact is turned to open.
Jumper for NC or 8,2 kΩ inputs
Jumper fitted for 8,2 kΩ resistive
edges.
Not
fitted
for
NC
mechanical edges
ALTERNATED BEEP
Transmitter
2 x 1,5 V AA batteries
4 years
868 MHz
100 m
4
-20 °C +70 °C
12 mA
IP 55
Mechanical and/or resistive 8,2 kΩ
Fax +39 0442 331054
03-2019
ARPO 58 receiver
ATTENTION: this card is to be
Back bracket
installed in a sheltered place.
Support
card
ON
1 2 3
OFF
NC
NO
relè R1
relè R2
NC
R1
12/24 Vac/dc
DELETING ALL TRANSMITTERS
1
Set to ON ALL of the programming dip-switches in the
ARPO 58 receiver
ON
1 2 3
OFF
2
Press the programming button in any ARPO 58
transmitter associated with the ARPO 58 receiver
3
Set to OFF ALL of the programming dip-switches in the
ARPO 58 receiver
LONG BEEP
ON
1 2 3
OFF
Actions to cure
Add the transmitter to the ARPO 58 receiver
Add an external aerial to the ARPO 58 receiver
Replace batteries in the ARPO 58 transmitter
Replace batteries in the ARPO 58 transmitter
Add an external aerial to the ARPO 58 receiver
The manufacturer is not liable for other applications out of the
scope here indicated.
Hereby, Meccanica Fadini snc, declares that this safety device
ARPO 58 is in compliance with the essential requirements and
other relevant provisions of Directives 2014/30/UE and
2014/35/UE. The declaration of conformity can be viewed on this
website: www.fadini.net in the product section.
2012/19/UE Directive
GB
Re. disposal of electric
and electronic waste
DISPOSE PROPERLY OF MATERIALS
ARMFUL TO THE ENVIRONMENT
A rp o 5 8
27
91
Receiver red led
RADIO
Programming
LINK
dip-switch
Aerial
RG58
NO
relè NC
NC
R2
R3-STOP
ALTERNATED BEEP
LONG BEEP
Werbung
