Herunterladen Diese Seite drucken

Vibrotech U025 Serie Gebrauchsanweisung Seite 2

Belüfter

Werbung

U025
1/2" GAS

6
BAR
40
70
AIR CONSUMPTION / LUFTVERBRAUCH
0.2 bar (2.9 psi)
U025
L/min
0.83
Ø 36mm / 1.42In
A
Ø 62mm / 2.44In
A
Ø 14mm / 0.55In
A
TROUBLESHOOTING TABEL
Symptom
Possible Causes
The fluidizers doesn't work. 1) Wrong pipeline connections.
2) Wrong diameter of the pipeline.
3)The distance between the air compressor system
and the first level of fluidisation nozzles / aeration
pads is higher than 10 m
The fluidizer doesn't fluidize
1) Wrong disposition of fluidizeron the silo.
correctly.
2) Wrong working pressure.
3) Insufficient number of the fluidizer.
TECHNICAL DATA / TECHNISCHE DATEN
48
31
-20°C ÷ 80°C
0.2 bar
U060
Cfm
L/min
0.03
30
Corrective action
1) Check pipeline connections.
2) Replace pipeline with correct diameter.
3) Place the air compressor system at a distance less than 10m from
the first level of the fluidizer.
1) Check the disposition of the fluidizer.
2) Increase the working pressure.
3) Increase quanties and/or levels of the fluidizer.
U060
30

-20°C ÷ 80°C
6
1 bar
BAR
AIR CONSUMPTION / LUFTVERBRAUCH
1 bar (14 psi)
Cfm
1.1
INSTALLATION / EINBAU
U025
(1)
WELD/SCHWEISSEN
B
U060
(1)
WELD/SCHWEISSEN
B
I100
(2)
B-C-D-E
Störung
Die Belüfter arbeiten
1) Falscher Anschluss der Rohrleitungen.
nicht.
2) Falscher Durchmesser der Rohrleitungen.
3) Der Abstand zwischen der
Luftkompressoranlage und der ersten Ebene der
Belüftungsdüsen/ -kissen liegt über 10 Meter.
Der Belüfter lockert die Luft
1) Falsche Anordnung der Belüfter auf dem Silo.
nicht richtig auf.
2) Falscher Arbeitsdruck.
3) Zu wenige Belüfter.
I100
98
5
32
AIR CONSUMPTION / LUFTVERBRAUCH
0.2 bar (2.9 psi)
I100
L/min
2
C-D
C-D
(1/4" GAS)
(3)
TABELLE DER FEHLERSUCHE
Mögliche Ursachen
1) Den Anschluss der Rohrleitungen prüfen.
2) Mit Rohrleitungen austauschen, die den richtigen
Durchmesser haben.
3) Die Luftkompressoranlage in einem Abstand von bis zu 10 Meter
zur ersten Ebene der Belüfter anbringen.
1) Die Anordnung des Belüfters prüfen.
2) Den Arbeitsdruck erhöhen.
3) Anzahl und/oder Ebene der Belüfter erhöhen.

-20°C ÷ 80°C
6
0.2 bar
BAR
Cfm
0.07
(2)
(3) N° 2 - 1/2" GAS
(4) 3/8" GAS
(2)
(4) 3/8" GAS
(5)
NOT INCLUDED
NICHT INBEGRIFFEN
F
Abhilfe

Werbung

loading

Diese Anleitung auch für:

U060 serieI100 serie