Seite 3
Montageanleitung Leaf Axial 4 Ventilation...
Seite 4
Montageanleitung Leaf Axial 4 min. 1 mm² max. 1,5 mm²...
Seite 5
Montageanleitung Leaf Axial 4 Ventilation...
Seite 6
Montageanleitung Leaf Axial 4 Performance Curve Axial 4 m³/h 28,5 mm 150 mm 94 mm Level 1 (Low Speed) Level 2 (High Speed) Extra: No. 531298 www.marley-shop.de...
Seite 7
Montageanleitung Leaf Axial 4 Lieber Kunde, Der Raumlüfter verursacht keine Störungen hinsichtlich Radio- oder Fernsehgeräten (Richtlinie 2004/108/EG). bevor Sie mit dem Einbau beginnen, sollten Sie die nachfolgende Anleitung AUFMERKSAM lesen, um die Sicherheit und korrekte korrekte Funktionsweise des Geräts zu gewährleisten.
Montageanleitung Leaf Axial 4 Der IP-Schutzgrad kann nur gewährleistet werden, wenn der Ein- Die Grundplatte des Gehäuses mit den im Lieferumfang enthal- bau des Geräts gemäß der vorliegenden Anleitung durchgeführt tenen Dübeln und Schrauben befestigen (siehe Abbildung 2). wurde. Der Hersteller lehnt jegliche Haftung für Schäden an Personen, Tieren oder Gegenständen ab, die aufgrund unsachgemäßer Ver-...
Montageanleitung Leaf Axial 4 alle Kabel richtig verlegt sind. Die Frontabdeckung wieder in die dafür vorgesehene Position EINSTELLUNGEN und FUNKTIONSWEISE: bringen und sicherstellen, dass sie nicht ohne den Gebrauch von Wenn zum ersten Mal Spannung anliegt, führt der Lüfter für eini- Werkzeug abgenommen werden kann (siehe Abbildung 10).
Montageanleitung Leaf Axial 4 Entsorgung Innerhalb der EU weist dieses Symbol darauf hin, TECHNISCHE DATEN* dass dieses Produkt nicht über den Hausmüll en- tsorgt werden darf. Altgeräte enthalten wertvolle recyclingfähige Materialien, die einer Verwertung Ventilator Axial 4 zugeführt werden sollten und um der Umwelt...
Seite 11
Montageanleitung Leaf Axial 4 Dear Customer, To guarantee the safety and correct working of the appliance, Prior to piping installation, consult the municipal by-laws please read the following instructions CAREFULLY before begin- on air outlets and request permission from the person responsi- ning the installation.
Montageanleitung Leaf Axial 4 porating a switch in the fixed wiring that meets electrical instal- lation standards. The appliance must be permanently connected with fixed installation wiring, fitted in the wall and entering the appli- ance through the rear side (see fig. 6).
Montageanleitung Leaf Axial 4 function is activated and the fan will operate at maximum speed. Once the level of humidity falls below the set value, the device will continue to operate at maximum speed for the period of TECNICAL DATA* time set in the Timer function, and will eventually stop if S1=OFF or continue to operate at low speed if S1=ON.
Seite 14
Montageanleitung Leaf Axial 4 Disposal This marking indicates that this product should not be disposed with other household wastes through- out the EU. To prevent possible harm to the envi- ronment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sus- tainable reuse of material resources.
Seite 15
Montageanleitung Leaf Axial 4 Ventilation...
Seite 16
Ventilation eine Marke der Marley Deutschland GmbH Adolf-Oesterheld-Str. 28 31515 Wunstorf Tel.: +49 5031/53-600 Mail: info@leaf-ventilation.de www.leaf-ventilation.de...