Setting The Alarm Clock; Activate/De-Activate Alarm Function - Audizio TOULON Micro HiFi System Bedienungsanleitung

After plugging the DC power adapter into the unit, "00:00" will appear and blink on the LCD display.
1. In Power Off (Standby) mode, press and hold CLOCK SET on remote control or main unit, the 24 HOUR format "24H" will
appear on display.
2. Press or on remote control or main unit to select 24 Hour format if desired. Otherwise, press CLOCK SET to
confirm 12 Hour clock format and enter clock setup mode. Hour digits will be flashing.
3. Press or on remote control or main unit to adjust the hour. Press and hold the button for fast advance/reverse
setting.
Note: Make sure the hour is set so that the PM indicator is displayed correctly.
4. Press CLOCK SET on the remote control to confirm the hour setting, the minute digits will flash to prompt for input.
5. Press or on the remote control or main unit to adjust the minute. Press and hold the button for fast
advance/reverse setting.
6. Press CLOCK SET on remote control again to complete the setting.
NOTE: The clock and radio station presets will need to be reset if the power is interrupted or in the event of a power outage.
"00:00" will appear and start blinking on the LCD display to notify you that the power was interrupted and the clock will need
to be reset. Please follow above steps 1-6 to reset the clock.
The unit will show the current time in standby mode. To check the current time in Power ON mode, press CLOCK SET on main
unit or remote control, the current time will show for 5 seconds and then return to the previous screen.

SETTING THE ALARM CLOCK

This function allows the system to turn on automatically and wake you using a beeping alarm, CD/USB/FM music or buzzer.
Timer start time (ON):
1. Press and hold, in standby mode, the TIMER button on the remote control until the display shows "On", and the hour digits
flash.
2. Press the or buttons to adjust the hour digits, and then press the ENTER button to confirm. The minute digits will
flash on the display.
3. Press the or buttons to adjust the minute digits, and then press the ENTER button to confirm.
Timer end time (OFF):
4. When the "On" Timer Clock is set, the display will show "OFF" and the hour digits will flash.
5. Press the or buttons to adjust the hour digits, and then press the ENTER button to confirm. The minute digits will
flash on the display.
6. Press the or buttons on the remote control to adjust the minute digits, and then press the ENTER button to confirm.
7. Press the or buttons to select CD, USB, FM or BU (buzzer) mode, then press the ENTER button to confirm. The
display will show "VOL#".
8. Press the or buttons to adjust the volume, and then press the ENTER button to confirm.
9. Press the TIMER button to select "Timer On", the Timer is set.
10. In standby mode, the icon "
NOTE:
If "Wake to CD/USB" is selected but a CD or USB drive are not inserted, the alarm will default to the Beeping Alarm
automatically when the alarm time is reached.
For 'Wake to Radio", the system will default to the last FM radio station listened to prior to switching off.
The crescendo alarm will increase to the volume level you have set.

ACTIVATE/DE-ACTIVATE ALARM FUNCTION

1. To activate the ALARM, press the TIMER button, and the alarm icon "
2. Cancel the ALARM function by pressing the TIMER button again. The alarm icon "
WAKE TO RADIO, CD/USB OR BUZZER ALARM
•When the alarm time is reached, the CD/USB, radio or beeping alarm will sound for 60 minutes, then shut off and reset itself
for the following day (without pressing the snooze button).
•To stop the alarm immediately after it sounds, press the POWER button on remote control or on main unit once. It resets
itself for the following day.
•To cancel the following day alarm, tap the TIMER button once, the alarm icon "
1. Tap the POWER/STANDBY button on main unit or remote control to turn on the unit.
2. Tap the SOURCE button on main unit or remote control to select FM mode.
3. To manually tune to a specific radio station, tap the TUNE
repeatedly. Use this manual tuning method to tune in to weaker stations that are bypassed by Automatic Tuning method.
4. To automatically tune to the next available radio station, press and hold the
control for 1-2 seconds until "SCA" readout appears on the display, then release the button. The tuner will stop scanning
when it receives the next broadcasting station of adequate signal strength.
" will show on the display to indicate the Timer is On.
" will show on the LCD display.
" will disappear from the LCD display.
" will disappear from the LCD display.
or button on either main unit or remote control
or
6
buttons on main unit or remote