Technical Data; Maintenance Instructions - Rodcraft RC7001 Bedienungsanleitung

English (English)
EN

1. Technical Data

Speed Power
Model
1 2
[Nm] [rpm]
max. pressure 6.3bar(90psi)
ah : Vibration level, k Uncertainty ; LpA Sound pressure dB(A), KpA = KWA = 3 dB Uncertainty.
Declaration of noise and vibration statement (ISO 15744 and ISO28927-1, ISO28927-3, ISO28927-12)
All values are current as of the date of this publication. For the latest information please visit www.rodcraft.com
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with
the declared values of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assess-
ments and values measured in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual
user are unique and depend upon the way the user works, the workpiece and the workstation design, as well upon the exposure time and the
physical condition of the user. We, RODCRAFT PNEUMATIC TOOLS , cannot be held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. This
tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at
www. pneurop.eu/uploads/documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf. We recommend a programme of health surveillance to
detect early symptoms which may relate to noise or vibration exposure, so that management procedures can be modified to help prevent future
impairment.
2. Machine type(s)
• This product is designed for removing material using abrasives. No other use permitted. For professional use only.
• Please read the instructions carefully before starting the machine.
3. Operation
• Fix the accessories properly to the tool.
• Connect device as shown in Fig. 01.
• To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
4. Lubrication
Motor
Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet
once a day.

5. Maintenance Instructions

• Follow local country environmental regulations for safe handling and disposal of all components.
• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your
nearest authorised dealer for advice on technical service or if you require spare parts.
• Always ensure that the machine is disconnected from energy source to avoid accidental operation.
• Disassemble and inspect the tool every three 3 months if the tool is used every day. Replace damaged or worn parts.
• High wear parts are underlined in the parts list.
6. Disposal
• The disposal of this equipment must follow the legislation of the respective country.
• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.
• Repair only by technical maintenance staff.
7. Declaration of conformity
We : Desoutter GmbH, Edmund-Seng-Str. 3-5, 63477 Maintal, Germany
Machine type(s): Die Grinder / Angle Grinder / Angle Sander / Polisher
Declare that the product(s): RC7001 / RC7102 / RC7103 / RC7601 / RC7602
Origin of the product : Taiwan
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery"
2006/42/EC (17/05/2006) applicable harmonised standard(s) : EN ISO 11148-7:2012 EN ISO 11148-8:2012 EN ISO 11148-9:2012
Name and position of issuer : Pascal Roussy (R&D Manager)
Place & Date : Saint-Herblain, 15/10/2021
Technical file available from EU headquarter. Pascal Roussy R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Her-
blain - France
Copyright 2021, Rodcraft
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is
not covered by Warranty or Product Liability.
Pad / Spindle Air
Collet Thread consumption
3 4 5
[inch] / [l/s]
Operator's Manual
Die Grinder / Angle Grinder / Angle Sander / Polisher
Weight Dimension Air inlet Inner hose
Axbxc
6 7 8
[kg] [mm] [inch]
Serial Number: From A00501 to Z99999
© Rodcraft-8956002065
RC7001 / RC7102 / RC7103 / RC7601 / RC7602
Sound Pressure Sound
diameter L Power
PA
L
9 10
[mm] [dB(A)] [dB(A)]
Vibrations
a K
hd
WA
11 12
[m/s ] [m/s ]
2 2
5