Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3) Release the locking screw (e) on the hinge, adjust
the desired inclination of the monitor and fasten the
screw again.
4) To install the monitor in an upright way, put the base
on a horizontal surface (fig. 4). If required, fasten it
with two screws to obtain a higher stability.
For wall mounting, fasten the base with two
screws (fig. 5).
ATTENTION: For installation in the car, screw
down the base at a stable place so that it will not
work loose and become a dangerous projectile
together with the monitor.
5 Connection
For use in the car, lay the cables in such a way that
their insulation will not be damaged.
Connect the monitor via the distribution cable provided
to the video outputs of the video sources (e. g. cam-
era, DVD player, etc.): Connect the 3.5 mm plug to the
jack AV IN (7) of the monitor, connect the RCA plug
"AV1" to the first video source and the RCA plug "AV2"
to the second video source. When using the camera of
a rear view system as a video source, connect it to
"AV2"
chapter 5.1.
For power supply via the 230 V mains, connect the
power supply unit provided to the power supply jack (6)
of the monitor and to a mains socket (230 V~ / 50 Hz).
For operation in the car, connect the power supply jack
of the monitor to the 12 V socket of the vehicleʼs elec-
trical system (cigarette lighter socket) via the cigarette
lighter cable provided.
5.1 Automatic switching to the camera image in
car rear view systems
For use in a car rear view system, the monitors allows
connection in such a way that it will automatically
switch to the image of the camera (video source "AV2")
when you put the car into reverse. For this purpose,
connect the connector of the single-core cable pro-
vided to the input BACK (8) and the open cable end to
the +12 V cable for the reversing light.
6 Remote Control
The remote control is supplied with a battery. Prior to
initial operation, remove the foil at the battery support
on the rear side.
When using the remote control, always direct it towards
the IR sensor (1) of the monitor. If it fails to function or
if its range decreases, replace the battery: Push the lug
of the battery support to the right (arrow 1 in fig. 6) and
remove the support (arrow 2). Insert a 3 V button cell
of the type CR 2025 (positive pole upwards) into the
support and push the support back in.
8
‘
If the remote control is not in use for a longer period of
time, remove the battery from the remote control as a
precaution so that it will not be damaged in case the
battery should leak.
7 Operation
1) In the stand-by mode, the button
itor will light up. To switch on the monitor, press this
button or press the button
trol. The button
(3) is no longer illuminated. The
monitor will display the image of the last video source
selected and the insertion "AV1" for video source 1 or
"AV2" for video source 2 will appear for a few
seconds. (If the monitor does not receive any video
signal from the video source selected, the screen is
blue and "AV1" or "AV2" is inserted permanently.)
Press the same button to set the monitor to
stand-by again. To switch off completely, discon-
nect the monitor from the power supply. If the mon-
itor is not in use for a longer period of time, also dis-
connect the power supply unit or the cigarette
lighter cable from the socket; they will have a low
power consumption, even if they are not connected
to the monitor.
2) To switch between the video sources, press the
button V1/ V2 (5) on the monitor or the button V1\V2
(11) on the remote control. The identification for
the video source selected ("AV1" or "AV2") will be
inserted for a few seconds..
If the monitor is part of a car rear view system and
has been connected accordingly (
it will automatically switch to the camera image
when you put the car into reverse.
3) The image parameters brightness, contrast and
colour intensity can be changed with the arrow
buttons (10) of the remote control:
buttons
for brightness
buttons COL
for colour intensity
buttons
for contrast
Press the corresponding arrow button to increase
L
M
(
) or decrease (
) the value on a scale from 0 to
100 (also possible via the menu
scale will disappear shortly after the last button has
been pressed.
The parameters changed remain memorized as
MEMORY
image adjustment
the monitor. When switching over to another image
adjustment with the button P.P (12), the individual
values are, however, reset to the factory settings
(
step 4).
(3) on the mon-
(9) on the remote con-
chapter 5.1),
step 6). The
even after switching off
Werbung
Inhaltsverzeichnis
