Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
machine is provided with a mechanical, electronic and
thermal overload safety system. Whenever the engine is
switched off due to overload, it must be switched on again
as soon as possible to cool the engine. Then let the drill
turn for a minimum of 1 minute.
1 - Electronic / Thermal
Whenever the engine is heavily overloaded , the overload
indication (LED) on top of the handle will start fl ashing.
The pressure on the diamond drill bit must than be reduced.
When the motor is overloaded too long, the LED fl ashes
continuously and the machine will switch off automatically.
2 - Mechanical
If the drill bit suddenly gets stuck, the slip coupling is
activated to disconnect the main axis from the engine.
Make sure you switch off the engine immediately and
remove the drill from the hole. When the slip coupling is
activated for a longer periods, the mechanical slip must be
re-tuned by a recognised expert.
Drilling with water cooling - Water connection
IF APPLICABLE
The drilling machine is equipped with a water tap, which
includes a 'Gardena' connection. Make sure that the core
drill is suffi ciently cooled and that the slurry is properly
discharged. The maximum permitted water pressure is 3
bars. Always use clean water to enlarge the life span of
the internal water seals. In case of leakage, the drilling
machine has to be checked IMMEDIATELY by a certifi ed
mechanical expert.
Dry drilling - Dust Extraction
IF APPLICABLE
For dry drilling only use designated drill bits. Dry drilling is
only possible in masonry, brick/block and sandstone.
Dust released during dry drilling is dangerous to your
health. Therefore
a dust extraction system specially
intended for this purpose must be used, and if necessary,
a dust mask worn. The use of a dust extraction system
is also required to optimize the life time of the diamond
drill bit. To prevent clogging of the dust extraction system
it is essential that the materials which are being drilled are
completely dry. Information about dust extraction systems
is available at your diamond tools supplier.
ENVIRONMENTAL PROTECTION
According to the European regulation
2012/19/EU,
responsible to recycle old electric drill
motors. You are therefore requested to
return old CORE Powertools electric drill motors to your
local reseller.
NMHX001
22-01-2015
All manuals and user guides at all-guides.com
CORE
Powertools
is
WARRENTY
For the machine, a guarantee period of 12 months applies
from the moment of delivery. Guarantee claims must be
shown by submission of purchase invoice. The guarantee
includes the repair of defects which have occurred and can
be linked by to material or manufacturing faults.
Not covered by guarantee:
• Defects or damages which have arisen due to incorrect
use or connection.
• Machine overload.
• When maintenance has been carried out incorrectly or
badly.
• Information in the manual has not been properly followed.
• The machine is used by unqualifi ed persons.
• If the machine is used for purposes for which it is
unsuitable.
• The machine is repaired using unoriginal parts.
• If the machine encryption is damaged or deleted.
• If defects are caused by fi re, damp and/or transport.
EMISSION
Typically the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level 105
dB(A). Uncertainty K = 3 dB.
WEAR HEARING PROTECTION!
The measured average vibration is less then 2,5 m/s²,
Measured values determined according to EN 60745.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents:
EN 60745-1; EN 61000; 2006/42/EC; 2004/108/EC;
2002/95/EC
Director: N.J.M. Knijnenburg
07.09.2010
CORE Powertools B.V.
Aartsdijkweg 67, 2676 LE Maasdijk, The Netherlands
ENGLISH – ORIGINAL INSTRUCTIONS
13
Werbung
Inhaltsverzeichnis
