Inhaltszusammenfassung für Camille Bauer SIRAX TI 807-6
Seite 1
All manuals and user guides at all-guides.com Betriebsanleitung Passiver DC-Signaltrenner SIRAX TI 807-6 Mode d’emploi Séparateur galvanique passif SIRAX TI 807-6 Operating Instructions Passive DC signal isolator SIRAX TI 807-6 TI 807-6 B d-f-e 108 151-01 03.07 Camille Bauer AG Aargauerstrasse 7...
Seite 2
All manuals and user guides at all-guides.com...
Seite 3
All manuals and user guides at all-guides.com Betriebsanleitung Passiver DC-Signaltrenner SIRAX TI 807-6 Mode d’emploi Séparateur galvanique passif SIRAX TI 807-6 Operating Instructions Passive DC signal isolator SIRAX TI 807-6 Sicherheitshinweise, die unbedingt beachtet wer- den müssen, sind in dieser Betriebsanleitung mit folgenden Symbolen markiert: Les conseils de sécurité...
Passiver DC-Signaltrenner SIRAX TI 807-6 Mode d’emploi Séparateur galvanique passif SIRAX TI 807-6 Operating Instructions Passive DC signal isolator SIRAX TI 807-6 1. Erst lesen, dann … Der einwandfreie und gefahrlose Betrieb setzt voraus, dass die Betriebsanleitung gelesen und die in den Abschnitten 5.
All manuals and user guides at all-guides.com 5. Mechanische Codierung des Max. Bürde: Steck-Moduls 1000 Ω bei der Standard- (Nicht Ex-) Ausführung 500 Ω bei Ex-Ausführungen Wenn die Gefahr einer Verwechslung besteht, dass (Eingangssignale «eigensicher») Steck-Module in falsche Steckplätze gelangen 500 Ω...
All manuals and user guides at all-guides.com 6. Elektrische Anschlüsse Signaltrenner mit zwei oder drei Trenn- und Über- tragungskanälen Der Signaltrenner SIRAX TI 807 wird auf einen Geräteträger BP 902 aufgesteckt. Die elektrische Verbindung zwischen Signaltrenner und Geräteträger erfolgt über einen 96-poligen Rückseite Steckverbinder (Bauform C, DIN 41 612).
All manuals and user guides at all-guides.com 10. Demontage-Hinweis 7. Montage 1. Schnellverschluss um 90° drehen. Der Signaltrenner SIRAX TI 807 wird auf einen Geräteträger 2. Steck-Modul herausziehen. BP 902 aufgesteckt. Bei der Festlegung des Montageortes (Messortes) ist zu beachten, dass die Grenzen der Betriebs- temperatur nicht überschritten werden: –...
Mode d’emploi Séparateur galvanique passif SIRAX TI 807-6 Operating Instructions Passive DC signal isolator SIRAX TI 807-6 1. A lire en premier, ensuite … Pour un fonctionnement sûr et sans danger, il est essentiel de lire le présent mode d’emploi et de respecter les recommandations de sécurité...
All manuals and user guides at all-guides.com 5. Codage mécanique du module Charge max.: embrochable 1000 Ω pour l’exécution standard (non-Ex) 500 Ω pour les exécutions Ex (entrées à «Sécurité intrinsèque») En cas de risque d’embrocher les appareils dans une place inappropriée, la norme EN 50 020, chapitre 6.3.2 500 Ω...
All manuals and user guides at all-guides.com 6. Raccordements électriques Séparateur galvanique avec deux ou trois circuits de séparation Le séparateur galvanique SIRAX TI 807 est embroché dans un support d’appareils BP 902. Les connexions électriques entre le séparateur galvanique et le support sont assurées Face arrière par un connecteur à...
All manuals and user guides at all-guides.com 7. Montage 10. Instructions pour le démontage Le séparateur galvanique SIRAX TI 807 est embroché dans 1. Tourner la fixation rapide de 90°. un support d’appareils BP 902. 2. Retirer le module embrochable. Pour la détermination de l’endroit de montage (endroit de mesure) il faut faire attention que les valeurs limites de la température de fonctionne-...
Mode d’emploi Séparateur galvanique passif SIRAX TI 807-6 Operating Instructions Passive DC signal isolator SIRAX TI 807-6 1. Read first and then … The proper and safe operation of the device assumes that the Operating Instructions are read carefully and the safety warnings given...
All manuals and user guides at all-guides.com 5. Mechanical coding of the plug-in module Max. burden: 1000 Ω for the standard (non-Ex) version Where there is a danger of inserting a module in the 500 Ω for Ex versions wrong slot, the possibility has to be excluded as (input signals “intrinsically safe”) prescribed in EN 50 020, Section 6.3.2.
All manuals and user guides at all-guides.com 6. Electrical connections Signal isolator with two or three isolation and transmission channels The signal isolator SIRAX TI 807 is plugged onto a backplane BP 902. A 96 pin connector (Model C, DIN 41 612) estab- Back lishes the electrical connections between the transmitter and the backplane.
All manuals and user guides at all-guides.com 7. Mounting 10. Releasing the signal isolator The signal isolator SIRAX TI 807 is plugged onto a backplane 1. Rotate the quick release screws 90°. BP 902. 2. Withdraw the plug-in module. When deciding where to install the signal isolator (measuring location), take care that the limits of the operating temperature are kept: –...