Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CATALOG
EN
Overview............................................................... 02
Installation Steps.................................................. 03
Using Steps ........................................................... 09
Specifications ....................................................... 11
Attentions ............................................................. 11
3. Push the ball joint firmly into the groove on the back of the
car mount, then tighten the grip nut.
4. Find a suitable place in your automobile outlet, insert the
car mount. Push the air vent clip lever according to the
thickness of the blade, then fix the car mount. Adjust the
angle of the car mount to fit the sight line.
Using Steps
1. Press the clamp arm button then the clamp arms open
automatically.
2. Put the phone into the car mount, then press hard on both
sides of the clamp arms to tighten the clamp arms to
ensure the mobile phone is fixed firmly.
Overview
Clamp Arms
3-level Air Vent Clip Lever
Ball Joint
3-level Air Vent Clip
Screw Knob
Ball Joint
01
02
Method 2 - Using with the Twist-lock Air Vent Clip
1. Unscrew the grip nut from the car mount and remove it.
2. Pass the ball joint through the grip nut from the smaller
opening side.
05
06
3. After using, please press the clamp arm button again to open
the clamp arms and take out the mobile phone as shown in
the picture.
09
10
Installation Steps
Method 1 - Using with the 3-level Air Vent Clip
Clamp Arm
Button
Open
Tighter
Grip Nut
II.
Tighter
1.8mm-2.5mm /
0.07inch-0.10inch
Attention:
1. The air vent clip was opened when the lever turns to the
right (as shown in picture1). The lever has 3-level thickness
options. The air vent clip will be tighter gradually when
turning the lever to left. Please adjust the air vent clip lever
suitably according to the thickness of your air vent blade.
2. Please adjust the air vent clip properly, and do not use the
air vent clip too tight. When the air vent clip is available in
Twist-lock
middle thickness, please do not adjust it to the smallest
thickness, otherwise, the air vent clip might be damaged.
Air Vent Clip
3. Push the ball joint firmly into the groove on the back of the
car mount, then tighten the grip nut.
4. Twist the screw knob to adjust the opening size of the clip
to fit the air vent.
Specifications
Product Name
Model
Applicable Places
Applicable Model
Package List
The parameters above are derived from the laboratory of VANMASS®.
The actual parameters would be different because of products
and other factors. The image shown here is indicative only.
Attentions
Avoid dropping.
●
Do not disassemble.
●
Please install the car mount on a suitable place before
●
driving, do not operate or adjust the car mount during
driving.
Do not install the car mount in places which interfere with
●
airbag or driving.
Please do not twist the air vent clip too tight, to protect the
●
air vent blade and air vent clip.
Keep the car mount away from children.
●
英语
1. Unscrew the grip nut from the car mount and remove it.
I.
Tight
2.5mm-3.5mm /
0.10inch-0.14inch
2. Pass the ball joint through the grip nut from the smaller
opening side.
III.
Tightest
1.8mm / 0.07inch
03
04
5. Find a suitable place to insert the car mount. Tighten the
screw knob to fix the car mount. Adjust the angle of the car
mount to fit your sight.
The suitability of car air vent
The air vent clip could be compatible with horizontal and
verticle air vent outlets.
But they cannot support non-intensive, circular or
special-shaped air vent outlets.
07
08
Car Mount
CTEZ44
Air Vent
4.5-6.5 Inches Phone
Car Mount x1,
Air Vent Clip x2,
User Manual x1
11
Werbung
