VANMASS B08CZFT8R4 Bedienungsanleitung

CATALOG
EN
Product overview .................................................................02
Compatibility........................................................................04
Align the phone to the coil position ....................................05
The tips of LED indicator......................................................06
Assembly and installation steps ..........................................07
Place the dashboard pad .....................................................12
Switch on power supply, wireless charging ........................13
Instruction of clamp arms....................................................14
Specifications .......................................................................16
Attentions .............................................................................17
FAQs ......................................................................................18
01
Align the phone to the coil position
Please adjust the bottom tray to keep the phone and charging
coil aligned according to instructions. The mount charging area
is around the LOGO. Most smartphones charging area is on the
center of phone.
Scale Phone model
4.7" iPhone 8
5.0" iPhone X / Xs / Samsung Galaxy S7 / S8 / S9
iPhone Xs Max / XR / 8 Plus /
5.5"
Samsung Galaxy S7 Edge / S8+ / S9+ / S10 / S10e
6.3" Samsung Note 8 / Note 9 / S10+
05
3. Push the ball joint firmly into the groove on the back of the car
mount, then tighten the grip nut.
4. Find a suitable place in your automobile outlet, insert the car
mount. Push the air vent clip lever according to the thickness
of the blade, then fix the car mount. Adjust the angle of the car
mount to fit the sight line.
09
Switch on power supply,
wireless charging
1. Plug the car charger into the car's cigarette lighter base.
2. Plug the charging cable USB-A connector into the QC 3.0 fast
charging port of the car charger. Insert the charging cable
USB-C connector into the charging port of the car charger
mount to turn on the power.
Please use QC 3.0 car charger to connect with
the wireless car charger mount.
Tips: To realize the fast charging function, the charging cable
USB-A connector must be plugged into the QC 3.0 fast charging
port(the blue one).
13
Attentions
1. Please install and adjust the car mount to the suitable position
in advance. Do not install or adjust the car mount during
driving.
2. Do not install the car mount on the place where may obstruct
airbag working or driving.
3. Please do not disassemble the car mount.
4. Please turn on car air-condition (fan) in hot day or using the
wireless charger for a long time, it is helpful to cool down the
wireless car charger mount and let the charging speed up.
5. Please connect the wireless car charger mount to power
supply, at the same time, please warm up charger mount from
hot air blowing out of the vent. Because when the temperature
is lower than 0℃ (32℉), the charger's inner lithium battery
would be ineffective which may cause the clamps can not lock.
6. Keep the wireless car charger away from children.
7. WARNING: hazardous moving parts, keep fingers and other
body parts away.
The Tips of Suction Cup Usage
1. It will reduce the adsorbability when stick the suction cup on
the curved surface, plush cloth surface or uneven surface.
2. It is not recommended to attach the suction cup to leathers,
walls or film-coated glass surfaces becuase the strong
stickiness might damage these surfaces.
3. The dashboard pad is one-time use. Once stuck, it's hard to
remove. Once removed, it cannot be used again. Please choose
the appropriate position on the dashboard to install it.
4. If the suction cup is used frequently in high temperature, low
temperature or humid conditions, the adsorption forces would
be lower. After using for a period of time, if the suction is not
sticky enough, please take down the suction cup base and
wash it with warm water. It will be sticky again after drying.
5. Please guarantee the suction cup is covered by plastic wrap if
the suction cup holder is removed.
17
FCC ID Statement
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
21
Product overview
Hidden Pressure Switch
(Close Button)
Wireless Charging
Sensing Area
Clamp Arms
Silicone Pads
Touch Switch
(Open Button)
Micro-USB Charging Port
Bottom Tray
Grip Nut
3-level Air Vent Clip Lever
Ball Joint
3-level Air Vent Clip
02
The tips of LED indicator
Blue: Charging Red: Not Charging
State of Charging LED Indicator Display
red
The indicator turns off after 3
Power On
seconds.
Indicator turns off.
Standby
Charging Blue indicator lightening.
Metal or other foreign red
The indicator flashes 10 times:
matter detection / use
of incompatible car 1 second on, 1 second off, then off.
charger
The charger sounds the alarm when
the inner lithium battery is in the lower
Low Battery Warning power. The alarm is a charging signal.
The clamp arm can not close when it
lacks energy.
06
Method 2 ‒ Using with the suction cup
1. Unscrew the grip nut completely, let the ball joint through the
grip nut (the thread must face the groove) and firmly push the
ball joint into the groove on the back of the car mount.
2. Tighten the grip nut and adjust the angle of the holder to fit the
sight line. (Twist the extendable arm adjusting nut to adjust the
length of the arms. Twist the extendable arm retaining nut to
change the angle of the arms.)
10
Instruction of clamp arms
1. Touch the button on either side of the car mount and the clamps
will open automatically.
2. Put the phone into the car mount (to trigger the hidden pressure
switch), then the clamps will grip the phone automatically and
the wireless charging will start in a few seconds. The indicator
light will turn blue.
14
FAQs
The suitability of car air vent
Cannot support non-intensive, circular or special-shaped air vent.
The Suitability of Phone Case
If the phone case is as the follows, it will not suitable for this
product: Too thick (＞4mm / 0.16 inch) or with a bumpy, uneven
or rugged surface; comes with metal, magnet, a ring shape
bracket, metal sticker attached, credit card, Popsockets etc.
18
英语
Extendable Arm
Extendable Arm
Adjusting Nut
Ball Joint
Extendable Arm
Retaining Nut
Suction
Cup Lock
Suction Cup
Dashboard Pad
USB-A Fast
LED Indicator
Charging Port
USB-A Standard
Charging Port
Car Charger
Negative Pole
Contactor
Positive Pole
Contactor
03
Assembly and installation steps
Method 1 - Using with the 3-level Air Vent Clip
Open
Tighter
I.
Tight
2.5mm-3.5mm /
0.10inch-0.14inch
II.
Tighter III.
Tightest
1.8mm-2.5mm /
1.8mm / 0.07inch
0.07inch-0.10inch
Attention:
1. The air vent clip was opened when the lever turns to the right
(as shown in picture1). The lever has 3-level thickness options.
The air vent clip will be tighter gradually when turning the lever
to left. Please adjust the air vent clip lever suitably according to
the thickness of your air vent blade.
2. Please adjust the air vent clip properly, and do not use the air
vent clip too tight. When the air vent clip is available in middle
thickness, please do not adjust it to the smallest thickness,
otherwise, the air vent clip might be damaged.
07
3. If the installation position is not smooth enough, it is
recommended to use the dashboard pad in advance. Then
install the car charger mount on the dashboard pad. At last, fix
the suction cup in the same way like step 4. (If you are not using
the dashboard pad, go to step 4.)
4. Clean the windshield or dashboard where you want to install the
car mount then install the car mount in the cleaned area. Rotate
clockwise the suction cup lock to the lock marker to fix the
suction cup on the windshield or instrument panel. (Rotate
counterclockwise until the unlocking marker shows on).
11
3. Please press the top half of the phone to trigger the hidden
pressure switch if the clamps do not close (close button).
4. After using, please press the button on either side of the wireless
car charger, then the clamp arms automatically pop up, so that
you could take out the phone.
Open
button
15
Unable to charge / slow charge / red light would not
put out
1. Please check if the USB cable connected or the USB cable is
defective.
2. Please ensure that your phone supports wireless charging.
3. Please check your phone case to sure whether it could
support wireless charging. (Kindly check "the suitability of
phone case")
4. Adjust the wireless car charger's bottom tray. Align your
phone to the wireless charging sensing area.
5. Double check to see if there is an issue with the car
charger/in-car USB port. (Please plug the cable into QC 3.0
car charger if your phone supports fast charging. Normal 2.4A
/2.1A /1A car charger or USB Port cannot supply enough
power for wireless fast charging so that the phone will
charging slowly or even can not charging.)
6. The red light turns on and would not put out, which means
the wireless car charger mount detects metal, foreign matter
or incompatible car charger. Please check whether the phone
aligned to the coil position or not, the phone case suitability,
and the car charger compatibility.
Clamp arms not working
1. When the clamps don't open/close as normal, it is because
the hidden pressure switch is stuck. Please activate the
hidden switch of the wireless car charger.
2. If there is "Beep" warning when moving the wireless car
charger switch button, it means the Built-in Lithium Battery
is out of battery. Please insert the cable to connect the
charger with QC 3.0 car charger for power supply.
3. Low temperatures can shorten the battery life, which may
cause the clamps do not work properly. Please insert the
cable to connect the wireless car charger with QC 3.0 car
charger for power supply and turn on the warm wind blowing
of the car, to rise the inside temperature of your vehicle.
19
Compatibility
Please notice:
1. Make sure your phone could be compatible with Qi wireless
charging before using this wireless car charger.
2. Use a car charger to connect the wireless car charger mount
in full charging process.
3. Connect the wireless car charger mount by QC 3.0 car charger
if you have a wireless fast charging mobile phone.
Smart Mobilephone Car Charger Output Power
Qi-Compatible
+ 5V 2A = 5W
Phones
iPhone XR,
iPhone XS,
9V 2A
iPhone XS Max, + = 7.5W
Quick Charge 3.0
iPhone X, iPhone 8
Plus, iPhone 8, etc.
Samsung
Galaxy S10+, S10e,
S10, S9+, S9,
Note 8, Note 9, S8+,
S8, S7 Edge, S7, etc.
9V 2A
+ = 10W
Quick Charge 3.0
LG
G7 ThinQ, V30,
V30S ThinQ,
V35 ThinQ,
V40 ThinQ, etc.
04
1. Unscrew the grip nut from the car mount and remove it.
2. Pass the ball joint through the grip nut from the smaller
opening side.
08
Place the dashboard pad
Before installing the mount on uneven or textured surfaces, please
firstly stick the gel plastic dashboard pad on the dashboard,
which is one-time use. Just stick the pad on the dashboard and
press it hard for 1min then let it rest for 1 to 3 days to have high
stickiness.
Clean Press hard Waiting
Please wait 24 hours to use the dashboard pad
after stuck.
stickiness stickiness
reach reach
＜1 Hour ＜6 Hours
5%~10% 20%~30%
stickiness stickiness
reach reach
≥24 Hours ≥72 Hours
60%~70% 80%~100%
12
Specifications
Product Name Automatic car mount wireless charger
Model
CTEZ59
Input
5V 2A / 9V 2A
Output 10W (Max)
Charging Induction
≈(4-6)mm
Distance
The Maximum
Voltage of the Charger's 4.2V
Lithium Battery
Applicable Temperature 0℃ - 40℃ / 32℉ - 104℉
Compatible with iPhone, Samsung,
Applicable Model LG, Moto etc. (4-6.5 inches phones
supporting wireless charging)
Automatic car mount wireless
charger ×1, Charging cable ×1,
Package List
Air vent clip ×1, Suction cup ×1,
Dashboard pad ×1, Fast charge car
charger×1, User manual ×1
Fast charge car charger
Product Name
CCVZ18
Model
12V-24V
Input
USB1: 3.6-6.5V 3A, 6.5-9V 2A,
9-12V 1.5A
Output
USB2: 5V 2.4A
0℃ - 40℃ / 32℉ - 104℉
Applicable Temperature
The parameters above are derived from the laboratory of VANMASS®.
The actual parameters would be different because of products and
other factors. The image shown here is indicative only.
16
High temperature warning
High temperatures can also cause slow charging speed and
wireless car charger malfunction. (Possible reasons for a high
temperature: GPS; too many APPs are running at the same
time; the in-car temperature is too high; direct sun light; hot air
coming out from the air vent while the wireless car charger is
installed at the air vent.)
If you have any questions, please email us as follow and
we will respond to you as soon as possible.
Official Email: service@vanmasslife.com
WARNING
1. Risk of Fire and Burns. Do Not Open, Crush, Heat (above
manufacturer's specified maximum temperature) or incinerate.
Follow Manufacturer's Instructions.
2. Please do not replace the battery by yourself. Turn to
professional maintenance staff to replace the battery if needed.
Wrong reassembly or improper battery replacement may lead
to fire or injury.
20