VANMASS VMPI01008A Benutzerhandbuch

封底
VMPI�����A
Overview
Clamp Arms
Silicone Pads
Bottom Tray
Grip Nut
Release Button
��
Tips for Removing the Suction Cup
The suction cup is reusable, it can be removed in the following
way:
�. Rotate to unlock the suction cup.
�. Pull the tab on the suction cup to allow air to get into it, stick
a plastic putty knife and floss (at your own risk) underneath
to break the seal.
�. Once the seal is broken you will be able to remove it easier.
Assembly of Mount
�. Take out the grip nut on the mount, assemble it with suction up.
��
封面
User manual
Benutzerhandbuch
取扱説明書
Ball Joint
Telescopic Arm
Length Adjustment Knob
(Adjust the Length of
the Arm)
Suction
Cup Lock
Angle Adjustment Knob
(Adjust the Angle of
the Arm)
Suction Cup
Dashboard Pad
��
�. Find a suitable place, attach the car mount.
Using Steps
�. Press the release button on the back of the car mount
then the clamp arms open automatically.
��
封面反面空白页
Installation Steps
Tips for Placing the Dashboard Pad
Before installing the mount on uneven or textured dashboard,
please firstly stick the dashboard pad (only one-time use).
Tear off the red protective sticker on the pad, stick it to the
dashboard, press it hard for over � minute then let it rest for
�-� days to have high strong stickiness.
Waiting
Clean Press 1 min
1~3 days
After installing the dashboard pad, please wait for �� hours
before using it.
stickiness stickiness
＜� Hour ＜� Hours
reach reach
�%~��% ��%~��%
stickiness stickiness
reach reach
≥�� Hours ≥�� Hours
��%~��% ��%~���%
��
２. Put the phone in the car mount then press the clamp arms
to grasp the phone.
�. After using, please press the release button again to open the
clamp arms and take out the mobile phone as shown in the
picture.
��
封底反面
Tips for Using the Suction Cup
�. Clean the dashboard or windshield where you need to install
the car phone mount with alcohol pads or a wet cloth, wait
for it to dry.
�. After attaching the suction cup, rotate its base completely to
fix the suction cup.
�. It will reduce the adsorbability when sticking the suction cup
on the curved surface, plush cloth surface or uneven surface.
�. It is not recommended to attach the suction cup to leathers,
walls or film-coated surfaces since the suction cup is
designed with strong suction power which may cause
surface damage.
�. If the suction cup is used frequently in high temperature, low
temperature or humid conditions, the adsorption forces
would be lower (Please avoid to expose it to the sun
directly).
�. If the suction cup is not sticky enough after usage, please
take it down and wash it with warm water (no soapy water or
other liquids). It will be sticky again after drying.
�. Please ensure the suction cup is covered by plastic wrap
once removed.
��
Specifications
Product Name Car Mount
Model
CTVK��
Applicable Places Windshield, Dashboard
Car Mount �,
Suction Cup �,
Package List
Dashboard Pad �,
User Manual �
The parameters above are derived from the laboratory of VANMASS®.
The actual parameters would be different because of products
and other factors. The image shown here is indicative only.
Attentions
Avoid dropping.
●
Do not disassemble.
●
Please install the car mount on a suitable place before
●
driving, do not operate and adjust the car mount during
driving.
Do not install the car mount in places which interfere with
●
airbag or driving.
Keep the car mount away from children.
●
��