Herunterladen Diese Seite drucken

Elko EP RFSA-61M/MI/230V Bedienungsanleitung Seite 2

Funkgesteuerte schalteinheit

Werbung

RFSA-61M/MI, RFSA-66M/MI
Wireless switch unit
EN
Funkgesteuerte Schalteinheit
DE
Indication, manual control /
Anzeige, manuelle Steuerung
LED Un
LED STATUS
antenna connector /
Antennenanschluss
button /
Taste PROG
• LED Un - green - power supply indication.
• LED STATUS - red - status indication of individual channels.
Indicators of memory function:
On - LED blinks x 3.
Off - The LED lights up once for a long time.
• Manual control is performed by pressing the PROG button for less than 1s.
• Programming is performed by pressing the PROG button for more than 1s.
In the programming and operating mode, the LED on the component lights up at the same time
each time the button is pressed - this indicates the incoming command.
Compatibility /
Kompatibilität
The device can be combined with all system components, controls and devices
of iNELS RF Control and iNELS RF Control
2
The detector can be assigned an iNELS RF Control
protocol.
01234
5
0524
Functions and programming with RF transmitters /
Function button /
Funktionstaste
Description of button /
Beschreibung der Funktionstaste
The output contact will be closed by pressing the button and opened by releasing
the button.
For the correct execution of individual commands (press = closing / releasing the
button = opening), the time delay between these commands must be a min of .
1 x
1s (press - delay 1s - release).
Programming /
Programmierung
Press of programming but-
1
ton on receiver RFSA-61M/
MI (66M/MI) for 1 second will
activate receiver RFSA-61M/MI
(66M/MI) into programming
mode. LED is fl ashing in 1s in-
terval.
Drücken der Programmiertaste
am Empfänger RFSA-61M/MI
1 x
> 1s
PROG
(66M/MI) für 1 Sekunde aktiviert
den Programmiermodus des
Empfängers RFSA-61M/MI (66M/
MI). LED blinkt im 1s-Intervall.
Made in Czech Republic
antenna
integrated
under the
panel
Antenne
unter dem
Panel
integriert
Funktionen und Programmierung mit RF-Sendern
2
1 x
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech Republic | e-mail: elko@elkoep.com | Support: +420 778 427 366
ELKO EP Germany GmbH | Minoritenstr. 7 | 50667 Köln | Deutschland | E-mail: elko@elkoep.de | Tel: +49 (0) 221 222 837 80
www.elkoep.com / www.elkoep.de
LED STATUS for individual channels /
LED STATUS für einzelne Kanäle
LED Un
antenna connector /
Antennenanschluss
PROG buttons for individual channels /
PROG Tasten für einzelne Kanäle
• LED-Un - grün - Versorgungsanzeige.
• LED-STATUS - rot - Statusanzeige der einzelnen Kanäle.
Anzeige der Speicherfunktion:
Ein - LED blinkt 3x.
Aus - die LED leuchtet einmal lang.
• Manuelle Steuerung wird durch Drücken der PROG-Taste für weniger als 1s durchgeführt.
• Programmierung wird durch Drücken der PROG-Taste länger als 1s durchgeführt.
Im Programmier- und Löschenmodus leuchtet die LED am Aktor bei jedem Tastendruck gleichzei-
tig auf - dies zeigt den eingehenden Befehl an.
2
.
2
2
(RFIO
) communication
Der Ausgangskontakt wird durch Drücken der Taste geschlossen und durch Los-
lassen der Taste geöff net werden.
Für die korrekte Ausführung einzelner Befehle (drücken = Schließen / Loslassen
der Taste = Öff nen) muss die Zeitverzögerung zwischen diesen Befehlen min. 1s
(Drücken - Verzögerung 1s - Loslassen).
Select and press one button
on wireless switch, to this but-
ton will be assigned function
Button.
Wählen Sie und drücken Sie
eine Taste am funkgesteuer-
ten-Schalter, dieser Taste wird
die Funktion zugeordnet.
antenna part of the product
Antenne ist ein Teil des Produkts
Aktor kann mit allen Systemelementen, Bedienelementen und Elementen von
iNELS RF Control und iNELS RF Control
2
kombiniert werden.
Zum Aktor kann ein Detektor mit Kommunikationsprotokoll iNELS RF Control
(RFIO
2
) zugeordnet werden.
3
1 x
< 1s
PROG
02-58/2016 Rev.9
2
Press of programming but-
ton on receiver RFSA-61M/MI
(66M/MI) shorter then 1 sec-
ond will fi nish programming
mode. The LED lights up accor-
ding to the pre-set memory
function.
Drücken der Programmiertaste
am Empfänger RFSA-61M/MI
(66M/MI), kürzer als 1 Sekunde,
der Programmiermodus wird
beendet, LED Leuchtet nach
der eingestellten Funktion.
2/7

Werbung

loading

Diese Anleitung auch für:

Rfsa-61m/mi/24vRfsa- 66m/mi/230vRfsa-66m/mi/24vRfsa-61mRfsa-61mi