Setting Up The Pizza Oven; Before Baking; Pizza Stone; Operation - tepro Danbury Bedienungsanleitung

t
Step 6
4. Assemble the pizza shovel.
WARNING
Assemble the pizza peel (9).
• Please always keep the gas bottle in upright position.
• If the appliance is not in use, the gas must be turned off at the supply cylinder.
• The minimum distance for the appliance and the 20lb gas tank is 40 inches apart.

Setting up the pizza oven

Attention Risk of damage!
CONNECTING THE LIQUID PROPANE GAS CYLINDER
During use, the screws can loosen slowly.
1. The cylinder valve should be in OFF position.
– Check that all screws are tightened before use. If necessary,
2. Make sure the burner valve is in OFF position.
tighten all screws to guarantee stability.
3. Inspect the valve connections, port and regulator assembly. Remove debris and inspect the hose for damage.
– Place the pizza oven outdoors on a level, heat-resistant, solid
4. When connecting the regulator assembly to the valve, use your hand to tighten the nut clockwise until it tops.
surface.
5. Use of a wrench could damage the quick coupling nut and result in a hazardous situation.
– When using the pizza oven, the floor and wall surfaces can
occasionally be contaminated, e.g. from splashes of fat. Make
6. Open the cylinder valve fully by turning the valve counterclockwise.
sure that the subsurface is adequately protected against such
contamination.
7. Before lighting the oven, use a soap and water solution to check all connections for leaks.
8. If a leak is found, turn the cylinder valve OFF, and do not use the oven until local liquid propane dealer make repairs.

before baking

CLOSE THE LIQUID PROPANE GAS CYLINDER
• Wash off any coarse production residues with warm water,
avoiding the use of detergents or detergents.
1.Turn the oven burner valve OFF and make sure the oven is cool.
Pre-firing
2. Turn the liquid propane cylinder valve OFF by turning clockwise until it stops.
• Before baking for the first time, heat up the pizza oven for
a min. 15 minutes with a closed lid and high flame without
3. Detach the regulator assembly from the cylinder valve by turning the quick coupling nut counterclockwise.
food. The heat cleans the internal parts and burns away the
4. Place dust cap for cylinder valve outlet whenever the cylinder is not in use.
finishing residues of coloured parts. In the process, odours
and some smoke may develop. However, this is harmless and
only lasts a short time. Ensure sufficient ventilation.
LEAK TESTING
Pre-heating
GENERAL
• It is recommended to preheat the pizza oven for about 10-15
minutes before each use.
Although the gas connections of the appliance are leak tested prior packing and shipment, a complete test must be performed at the installation site
and before each use.Check all the gas connections for leak testing using the procedure listed below. If the smell of gas is detected at any time, you

Pizza stone

should immediately stop using and check the entire system for leaks.
• DO NOT use the stone over an open flame.
BEFORE TESTING • Avoid extreme temperature fluctuations in the stone.
DO NOT put frozen food on a hot stone.
Make sure all packing material has been removed from the appliance.
• The stone is fragile and can break if hit or dropped.
Make a solution of one part liquid detergent and one part water. You will need a spray bottle, brush or rag to apply the solution to the fittings.
• The stone is very hot during use and will stay hot for a long
time after use.
• DO NOT cool a hot stone with water.
16
P21098_TEPRO_1173_PelletPizzaofen_Danbury_DE_GB_210831.indd 16
A
B
C
D

Operation

Danger Risk of burning!
The pizza oven, contained pellets and baking items
get very hot during use so that contact with them can
cause serious burns.
– Keep away from hot parts as any contact can cause severe
burns.
– Always wear oven or BBQ gloves when baking. (Glove Cate-
gory II with regard to heat protection, e.g. DIN-EN 407. Glove
Operation guideline
must match the PSA regulation.)
Operation guideline – Use long-handled utensils with heat-resistant handles only.
1. Open the chimney (01) lid.
– Do not wear any clothing with wide sleeves.
1. Open the chimney (01) lid.
1. Open the vent chimney (01)
2. Close the door (08).
2. Close the door (08).
2. Close the door (08).
3. Add pellets (about 380 grams (0.8lb), reach to about 2/3 of the pellet colle
3. Add pellets (about 380 grams (0.8lb), reach to about 2/3 of the pellet c
(09)
5
31/8/2021 12:36 PM