Resetting To Factory Settings; Care And Cleaning; Declaration Of Conformity (Doc) - Renkforce RF-WMH-320 Bedienungsanleitung

"TouchLink" configuration
• Click "WiFi" at the bottom of the Mesh-Router's web interface and then open the item
"TouchLink" to configure the function on the configuration page.
• Here you can turn the function on or off using the slide button, you can configure the sharing
time for the connection that will become active after you have clicked the button and you
can change the WLAN SSID.
• You can also view a list with devices that are already connected and whether the connection
is active.
• Mark the box next to a device to delete it.
• Click the blue button to save changes or to delete a device.
Positioning the Mesh-Repeaters
• You need to find an appropriate location for the repeater(s) after the connection is working.
• Try different locations and select the final location with the best connection to the Mesh-
Router or an already installed Mesh-Repeater.
• Test the connection quality with your smartphone, for example, to make sure that the Mesh-
Repeater is not located too far away from the next device. The WLAN icon should have at
least 3 active bars.
Important! Once the repositioned WLAN repeater starts and the LED indicator is
steady blue, the connection is good. If the indicator is lit red, then the connection is
bad and insufficient. If that is the case, reposition the Mesh-Repeater.
If a Mesh-Repeater uses a wired connection, then the distance to the next device is
not a major issue, of course.

Resetting to Factory Settings

Proceed as follows to reset the product to factory settings.
• Plug the power adapter output into the "DC IN" socket (2) of the product.
• Plug the power adapter into a mains socket.
• Use the slide switch (3) to turn the product on and wait until the boot process has finished.
• Hold down the "Reset" button (4) for more than 6 seconds. Then release the button.
• The product will restart with the factory settings. This takes about 1 to 2 minutes.

Care and Cleaning

Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions
since these could damage the housing or even impair operation.
• Before cleaning, pull the power adapter out of the power socket and remove any connection
cables.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electrical and electronic equipment does not belong in the regular household waste.
Once the product becomes unusable, dispose of it in accordance with the relevant
statutory regulations.

Declaration of Conformity (DOC)

We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available at the following Internet
address:
www.conrad.com/downloads
Select a language by clicking a flag symbol and enter the order number of the prod-
uct in the search field; then you will be able to download the EU declaration of
conformity in PDF format.
Technical data
a) Product
Operating voltage ........................ 12 V/DC 1.5 A
Power consumption ..................... max. 1.5 A
Ports ............................................ 3x RJ45 10/100/1000 MBit/s, 1x WAN, 2x LAN; 1x USB
Number of antennas .................... 6; 4x 5 GHz, 2x 2.4 GHz
WLAN .......................................... EEE802.11b/g/n, 2.4 GHz, max. 300 MBit/s;
...................................................... IEEE802.11a/n/ac, 5 GHz, max. 1733 Mbit/s;
Frequency range/ ........................ 2.412 – 2.472 GHz, ≤ 13 dBm;
transmitting capacity .................... 5.150 – 5.250 GHz, ≤ 21 dBm
...................................................... 5.725 – 5.850 GHz, ≤ 14 dBm
Encryption protocols .................... WPA2; WPA
Modes of operation ...................... Mesh-Router/Mesh-Repeater
Dimensions (W x H x D) .............. approx. 134 x 116 x 125 mm
Weight ......................................... approx. 829 g per device
Operating conditions .................... 0 to +40 °C / 10 - 90% rel. humidity (noncondensing)
Storage conditions ....................... -10 to +70 °C / 10 - 90% rel. humidity (noncondensing)
b) AC adapter
Operating voltage ........................ 100 - 240 V/AC, 50/60 Hz, max. 0.5 A
Output .......................................... 12 V/DC, 1,5 A, 18 W
Output jack .................................. coaxial connector 5.5 x 2.5 mm
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE. *2300579_80_V2_0421_m_DM_4L