Safety And Compliance Information - ring 5B28S5 Bedienungsanleitung

ENGLISH
First, complete the in-app setup.
1. Make sure your Ring Alarm is disarmed.
2. In the Ring app, tap Set Up a Device and find the Contact Sensor
in the Security menu.
3. Follow the in-app instructions to complete setup.
Then, install the device in your home.
1. Choose the door or window where you'd like to install your Sensor
and magnet.
2. If the magnet is too large, open the back and remove the magnet
piece from the magnet case and mount it directly.
3. Line up the Sensor and magnet, with no more than 2.5cm (1")
between them.
4. Leave at least 1.3cm (1/2") space around the Sensor so you can
open the battery compartment.
5. Clean the area, then peel the backing from the mounting tape and
press the Sensor and magnet into place.
6. To install using screws you will need: Screws: 4x 3x21mm.
Anchors: 4x 5mm.
If you're using the Contact Sensor on a door you use often, choose
Main Door as the placement option. Main doors have Entry and Exit
Delays to prevent you from accidentally triggering the alarm.
How to change the battery.
Slide the sensor backwards and off the mounting bracket. Replace
the battery with fresh CR2032 cell batteries. Ensure that the battery
is inserted correctly. When inserting batteries, make sure the (+) is
facing up.
WARNING: Inserting the battery with the wrong polarity may damage
the device.
4
cs1-manual-safety-eu-84x111.indd 5 cs1-manual-safety-eu-84x111.indd 5

SAFETY AND COMPLIANCE INFORMATION

Use Responsibly. Read all instructions
and safety information before use.
SAFETY INFORMATION
WARNING! Failure to read and follow these
safety instructions before operation could result in
fire, electric shock, or other injury or damage.
WARNING! Your device should only be used in
accordance with the specific instructions for use
and intended purpose of the device. Using your
device in any way other than its intended purpose
could cause injury to yourself, others and/or
damage to the device or property.
CAUTION! The device is not waterproof and
as such should not be submerged in water, doing
so could cause injury to yourself, others and/or
damage to the device.
WATCH FOR SMALL PARTS! Your device and
accessories may present a choking hazard to
small children. Keep them out of reach of small
children.
Ring Contact Sensor is for indoor use only.
BATTERY SAFETY
This product contains lithium coin batteries. This
device requires batteries for use. Only use new
CR2032 3V batteries. Never mix old and new
batteries. Keep all of the batteries out of the reach
of children. Do not open, disassemble, puncture,
cut, bend, shred or heat the batteries and do not
allow metal objects to touch the battery terminals
on the device as they can become hot and cause
burns. Remove all batteries if they are worn out
or before storing your Device for an extended
period of time.
Dispose of all batteries in accordance with
applicable laws and regulations and do not
dispose of batteries by throwing them into a fire.
If any batteries begin to leak, take steps to prevent
the fluid from coming into direct contact with
skin or clothes as the fluid could be corrosive and
may be toxic. Remove the batteries and clean
the battery compartment in accordance with the
battery manufacturer's recommendations.
CAUTION! Danger of explosion if battery
is incorrectly replaced. Replace only with the
same or equivalent type recommended by the
manufacturer. Dispose of the used batteries
according to the manufacturer's instructions.
CHEMICAL BURN HAZARD! This product
contains lithium coin batteries. Do not ingest
batteries. If the coin cell battery is swallowed, it
can cause severe internal burns in just 2 hours and
lead to death. Keep all of the batteries out of the
reach of children. If you think batteries might have
been swallowed or placed inside any part of the
body, seek immediate medical attention.
PRODUCT SPECIFICATIONS
Model Number: 5B28S5
Electrical Rating: 2x CR2032 3V
Temperature Rating: 0°C - 49°C
EU CONFORMITY
Hereby, Ring LLC, declares that the radio
equipment Ring Contact Sensor (5B28S5) is
in compliance with Directive 2014/53/EU. The
full text of the EU Declarations of Conformity
are available at the following internet address:
ring.com/doc.pdf.
RADIO FREQUENCY COMPLIANCE
In order to protect human health, this device
meets the thresholds for exposure of the general
public to electromagnetic fields according to
Council Recommendation 1999/519/EC. This
device should be installed and operated with
at least 20 cm between the radiator and your body.
Wireless Features: Z-Wave
Maximum Equivalent Isotropically Radiated
Power: 868.40 - 869.85 MHz 4.38 dBm EIRP
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic
devices is regulated. Make sure you dispose of, or
recycle, your device in accordance with your local
laws and regulations.
5
15-01-2021 11:13 15-01-2021 11:13