Laserworld Ecoline Serie Bedienungsanleitung Seite 3

1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
Laser system, power cable, keys, interlock bridge plug, manual
2. Preliminary warning notices
• Please use this device only according to these operating instructions.
• Do not use the device if there are any visible damages on housing, connector panels, power
supplies or power cords.
Never look directly into the light source of a laser projector. Danger of damage to the
•
eyes or even blindness in extreme circumstances!
• This device must not be permanently connected to mains. Disconnect it from mains or use
the power button to switch if off if not in use.
• Do not operate the device at high humidity, in the rain or in dusty environments.
• Protect device against dripping or splashing water. Do not place any liquid filled containers
near to this device.
• Any warranty claims are void if the warranty label is removed or tampered with in any
way.
3. Initial operations, safety instructions
• Make sure to use correct voltage; see information on device & in this manual.
• Make sure that the device is not connected to mains during installation.
• Installation has to be done by technical experienced and qualified persons according
to safety regulations of the respective country.
• Always ensure that maximum permissible exposure (MPE) is not exceeded in
areas accessible to the public or members of staff.
• In some countries an additional inspection by technical control institutes could be
necessary.
• Connect an easily accessible interlock connector or circuit breaker to the projector.
• The power supply should be easily accessible.
• When installing the laser mount it with a minimum distance of 15 cm from walls and
objects.
• For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord
should be able to withstand tenfold the weight of the device. Please follow the accident
prevention regulations of professional associations and/or comparable regulations for
accident prevention.
• If the device has been exposed to great temperature changes, do not switch it on
immediately. Condensation (or any moisture / water formed) may damage device.
Never use dimmer, RC or other electronically switched sockets. Whenever
•
possible, do not use the laser projector together with large appliances (especially fog
machines) on the same mains!
4 / 28
Laserworld EL-230RGB Laserworld EL-230RGB
•
•
•
•
•
•
•
•
5.
•
•
•
•
•
•
Ensure sufficient ventilation and do not place the device on any warm or heat radia-
ting surface. Especially the ventilation openings must not be covered!
Ensure that device does not get overheated. Make sure that the device is not exposed
to spotlights (especially moving heads). Heat of spotlights could overheat laser in a little
while and leads to a degradation of performance.
This unit is intended for indoor use only.
4. Working on the device
This product has no user serviceable parts inside and should only
be maintained and serviced by a qualified engineer.
Be sure that the mains plug is not connected to the power
supply while installing.
Take off all reflecting things like rings, watches etc. before
starting to work with or at the projector.
Only use non-reflecting tools to work on device.
Wear protective clothing (like glasses, gloves etc.) accor-
ding to laser power and wavelength of the laser.
Service notes
Moisture and heat can reduce lifetime of the laser system dramatically and expires any
warranty claim.
Quick on/off switching of this device will reduce durability of the laser diode dramatically.
Avoid sharp knocks and shocks to this device and ensure sufficient protection during
transportation. Look after your Laserworld product.
To increase durability of your laser, protect device against overheating:
1. Always ensure sufficient ventilation.
2. Do not face spotlights (especially moving heads) to the device.
3. Check temperature after approx. 30 minutes with each new installation. If necessary
install the projector at a place with different temperature.
4. Keep the device dry. Protect it from moisture, rain and damp.
5. Switch off device when it is not needed. Diodes are switched on and can wear out
even if there is no visible laser output.
6. Please ensure the fans and heatsinks are clear from dust and debris otherwise the
risk of overheating may occur. If the unit and airways appear to be blocked then
please contact a qualified service engineer to maintain and service the product.
The devices of the Ecoline Series are not meant for professional applications. They are
not suitable for 24/7 operation.
Removal of the warranty label as well as damages to the device caused by impro-
per handling, neglect of the safety instructions and service notes will void the
warranty
5 / 28