Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Features
Supports the Wireless Standards IEEE 802.11b/g/n
with a data rate up to 150 Mbps
Easy installation via the receiver menu,
no additional software required
Rotating antenna: 90° in the vertical direction
and 180° in the horizontal direction
Supports 64/128-bit WEP, WPA
and WPA2 encryption
Connection indicator LED
Power supply via the receiver's USB port
Suitable for the receivers:
UFS 913 from software version V1.01,
UFS 923 from software version V1.03,
UFS 925, UFS 935
For indoor installation
Technical Specifi cations
Type
Part no.
Standard
Connection
Data rates
Operating temperature
Unit dimensions
mm
(W x H x D)
Electronic equipment is not household waste, sin accordance
with directive 2002/96/EC OF THE EUROPEAN PARLIAMENT
AND THE COUNCIL dated 27
electrical and electronic equipment, it must be disposed of
properly. At the end of its service life, take this unit for disposal
at a designated public collection point.
Connection
Connect the WLAN/USB adaptor to a free USB 2.0 port on your
Kathrein receiver. On most devices this can be found at the rear.
Please note that this procedure is currently available only for the
receivers listed above and the software versions shown.
Internet: www.kathrein.de
KATHREIN-Werke KG • Anton-Kathrein-Straße 1 - 3 • P.O. Box 100 444 • 83004 Rosenheim • GERMANY • phone +49 8031 184-0 • Fax +49 8031 184-306
UFZ 130
20410041
IEEE802.11b, 802.11g, 802.11n
USB 2.0 type A
11b: 1/2/5.5/11 Mbps
11g: 6/9/12/24/36/48/54 Mbps
11n (20 MHz):
MCS 0-7 (up to 72 Mbps)
11n (40 MHz):
MCS 0-7 (up to 150 Mbps)
°C
+0 to +40
15 x 155 x 15
th
January 2003 on used
936.4438/-/ZWT/0512/de - Technische Änderungen vorbehalten! Technical data subject to change.
Setting up
If you have not yet done so, now switch your receiver on.
Press the menu button to call up the main menu. In the menu,
select "Interfaces" and confi rm with "OK". Now select "Ethernet
Settings" and again confi rm with "OK". The following on-screen
display appears:
Use the arrow buttons to select the setting "On". To activate the
WLAN function you must then restart the receiver. After the restart,
call up this menu (Main menu - Interfaces - Ethernet Settings)
once again. In the menu, select the "WLAN Confi guration" line
and confi rm with "OK". The display lists all the wireless (WLAN)
networks that were found. In the menu, select the desired
wireless network and confi rm with "OK". Now you must input your
network PIN.
Make your selections
using the arrow buttons,
and confi rm each
selection with "OK".
Once you have input the
complete network PIN,
set the tick symbol and
confi rm with "OK".
To input your network PIN, call up the menu (Main menu -
Interfaces - Ethernet Settings) once again. In the menu, select
the "IP Confi guration" line and confi rm with "OK". The following
on-screen display appears (example):
See also ...
for UFS 913/923:
Operating manual
Part 2 "Main menu -
Interfaces", "Ethernet
Settings"
for UFS 925/935
Operating manual
Part 1 "Connection
and set-up", "Network/
Internet connection"
Select the required settings here, according to your circumstances.
You can then select "Test Connection" to test your settings, and
"Save" to save them. After you have successfully made your
settings, you will see the following on-screen display in the lower
part of the "Ethernet Settings" menu (example):
Press the menu button to exit the menu again.
Werbung
