Declaration Of Conformity (Doc); Technical Data; Care And Cleaning - Renkforce Rf-Wfd-300 Bedienungsanleitung

Setting a default network
If you have multiple networks under the
Profile
starts up, it connects to the default network (if available).
1. In the interface, click on the tab.
Profile
2. Select the network from the network list.
3. Click on
Set Default.
» The default network is set.
Setting up a virtual access point
The virtual access point allows other network hosts (e.g. computer, smart phone) to connect to the product.
The network frequency band is inherited from the WLAN network the product is connected to.
Requirements:
• The product is connected to a WLAN network.
Set up the virtual access point as follows:
1. In the bottom bar of the interface, check the
» The Virtual WiFi tab is added to the interface.
2. (If unchecked) check the
Start Virtual WiFi Soft AP
» The access point loads.
3. (If unchecked) check the checkboxes: Setting Internet Connection Sharing (ICS)
Public Network.
4. Click on Config.
» The access point configuration mask opens.
5. Configure the access point:
- Define an SSID (network name).
- Set network authentication and encryption.
Device compatibility: Ensure your devices support the selected option.
- Define a network password/key.
6. Click on to confirm the configuration.
OK
» The configuration mask closes.
» You can now connect network hosts (e.g. computer, smart phone) to the virtual access point using the
defined SSID and password/key.
c) Enable and configure AP mode
In access point mode (AP mode), the product provides a separate WLAN network.
You can set a frequency from the frequency band 2.4 or 5 GHz.
You connect network hosts (e.g. computer, smart phone) to the access point (AP) for network access.
Requirements:
• The product is connected to the computer.
• The computer is connected to a network.
• The network utility interface is open.
Enabling the mode
1. In the interface, click on Mode(M).
2. Select Point. The mode switches to AP mode.
Access
» AP mode is enabled.
Setting up the access point
1. In the interface, click on General.
2. (If unchecked) check the checkbox
Setting Internet Connection Sharing
» The access point loads.
3. Select the network you intend to share.
- Click on to refresh available networks.
Refresh
- Option 1: Uncheck Auto Select Public
on Apply to save.
- Option 2: Check the checkbox
Auto Select Public
4. Click on Config.
» The access point configuration mask opens.
5. Configure the access point:
- Define an SSID (network name).
- Select a frequency channel.
- Set network authentication and encryption.
Device compatibility: Ensure your devices support the selected option.
- Define a network password/key.
» The access point is configured.
» You can now connect network hosts (e.g. computer, smart phone) to the access point using the defined
SSID and password.

Care and cleaning

• Disconnect the product from the power supply before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
tab mark one of them as default. When the network utility
checkbox.
Virtual WiFi allowed
checkbox.
and
(ICS).
Network. Select a network from the dropdown menu. Click
Network. The network is selected automatically.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product con-
forms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity: www.conrad.
com/downloads
Enter the product item number in the search box. You can then download the EU declaration of
conformity in the available languages.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

Technical data

a) General
Operating voltage ................................. 5 V/DC via USB (min. USB 2.0, min. 500 mA)
Range ................................................... Indoors: max. 100 m / Outdoors: max. 300 m
Operating system support .................... Windows
Auto Select
Operating conditions ............................. 0 to +40 °C, 10 – 90 % RH (non-condensing)
Storage conditions ................................ -10 to +70 °C, 10 – 90 % RH (non-condensing)
Dimensions (W x H x D) ....................... Dock: approx. 63 x 31 x 47 mm
Weight .................................................. Dock: approx. 72 g
b) WLAN data
Network security ................................... WPA/WPA2/Shared Key
IEEE Class
802.11b 2.4 GHz
802.11g 2.4 GHz
802.11n 2.4 GHz
802.11ac 5 GHz
* for max. bandwidth connect the product to a USB 3.0 port on the computer.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
7 and higher / MacOS
®
Adapter: approx. 29.5 x 12 x 87 mm
Adapter: approx. 30 g
Frequency Transmission power
2412 – 2472 MHz <20 dBm
2412 – 2472 MHz <20 dBm
2422 – 2462 MHz <20 dBm
5150 – 5250 MHz <20 dBm
5725 – 5850 MHz 13.76 dBm
Bandwidth (max.)
11 Mbps
54 Mbps
300 Mbps
867 Mbps*
*2298216_v1_1020_02_jh_m_4L_(1)