Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Battery-Operated Night Light with PIR Sensor
Item No. 2335668
Intended use
The product is a battery operated night light with PIR sensor.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-
rooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating
instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Night light
• USB charging cable
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
This product is constructed according to protection class III.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions
carefully and especially observe
the safety information. If you do
not follow the safety instructions
and information on proper han-
dling in this manual, we assume
no liability for any resulting per-
sonal injury or damage to prop-
erty. Such cases will invalidate
the warranty/guarantee.
a) General information
• The device is not a toy. Keep it out of the
reach of children and pets.
• Do not leave packaging material lying
around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme tem-
peratures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases,
steam and solvents.
• Do not place the product under any me-
chanical stress.
• If it is no longer possible to operate the
product safely, take it out of operation and
protect it from any accidental use. Safe
operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in
poor ambient conditions or
- has been subjected to any serious trans-
port-related stresses.
• Please handle the product carefully. Jolts,
impacts or a fall even from a low height can
damage the product.
• Magnetic mounting plate with adhesive
• Operating instructions
• Consult an expert when in doubt about the
operation, safety or connection of the ap-
pliance.
• Maintenance, modifications and repairs
must only be completed by a technician or
an authorised repair centre.
• If you have questions which remain un-
answered by these operating instructions,
contact our technical support service or
other technical personnel.
b) LED light
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with
optical instruments!
c) (Rechargeable) batteries
• The rechargeable battery is permanently
built into the product and cannot be re-
placed.
• Never damage the rechargeable battery.
Damaging the casing of the rechargeable
battery might cause an explosion or a fire!
• Never short-circuit the contacts of the
rechargeable battery. Do not throw the
battery or the product into fire. There is a
danger of fire and explosion!
• Charge the rechargeable battery regularly,
even if you do are not using the product.
Due to the rechargeable battery technol-
ogy being used, you do not need to dis-
charge the rechargeable battery first.
• Never charge the rechargeable battery of
the product unattended.
• When charging, place the product on a
surface that is not heat-sensitive. It is nor-
mal that a certain amount of heat is gener-
ated during charging.
Charging the battery
Connect one end of the included cable to the microUSB DC 5V port on the product. Connect
the other end to a suitable power source.
An LED indicator besides the microUSB port will show the charging status:
- RED: charging in progress
- BLUE: battery fully charged
Mounting options
Important
• Locate the product away from appliances such as refrigerators, ovens, heaters, and
air conditioners. They can affect the sensitivity of the sensor.
• Solid objects such as glass and curtains between the sensor and a person can pre-
vent the sensor from activating the light.
a) Magnetic surface
The product has a rear magnet. You an attach it to a magnetic surface such as a refrigerator.
b) Mounting plate
If the surface is not magnetic, use the metal mounting plate.
1. Make sure the surface is clean, flat, smooth and non-porous.
2. Remove the adhesive tape and press and hold it against the surface for approx 1 minute.
3. Attach the product to the metal mounting plate.
c) Hanging hole
There is a hanging hole at the back of the product. Use it to hang over a protruding nail or
screw.
Operation
Use the mode switch to select a mode.
Mode
Description
ON
Always on
OFF
Switch product off
• The sensor activates when it gets dark.
• When the sensor detects motion, it will trigger the light.
AUTO
• The light will switch off approximately 30 seconds after no mo-
tion is detected within the detection range.
Care and cleaning
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the envi-
ronment.
Technical data
Input.............................................. 5 V/DC 1.0 A
Battery .......................................... 1x 3.7 V 1000 mAh 3.7 Wh Li-ion
Battery recharge time ................... approx. 2 hrs
Battery life ..................................... approx. 8 hrs continuous use
Lighting modes ............................. 3
Protection class ............................ III
Colour temperature ....................... 3000 K
Sensor .......................................... Activation: <15 lux (approx.)
Detection distance: 1 - 5 m
Detection angle: 90° (vertical) / 100° (horizontal)
Operating conditions ..................... -10 to +40 ºC, 20 – 80 % RH (non-condensing)
Storage conditions ........................ -25 to +55 ºC, 20 – 80 % RH (non-condensing)
Dimensions (W x H x D) ............... 80 x 91 x 14.5 mm
Weight .......................................... 70 g (incl. battery)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
*2335668_v1_0221_02_dh_m_en
Werbung
