Herunterladen Inhalt Inhalt Diese Seite drucken

Transporting Lithium Batteries; Working Instructions; Maintenance, Cleaning And Repair - Milwaukee M18 FPOVCL Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 31
NOTE: If the vacuum is accidentally tipped over, it could lose
suction. Turn o the vacuum and return it to an upright position.
The oat will return to its normal position.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture. Store the battery packs in a 30% - 50%
charged condition. Every six months of storage, charge the pack
as normal.
GB
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the appliance
before being charged;
Exhausted batteries are to be removed from the appliance and
safely disposed of.
If the appliance is to be stored unused for a long period, the
batteries should be removed.
The supply terminals are not to be short-circuited.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legisla-
tion requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated
to prevent short circuit. Ensure that battery pack is secured against
movement within packaging. Do not transport batteries that are
cracked or leak. Check with forwarding company for further advice.

WORKING INSTRUCTIONS

Only use the appliance if it is in perfect condition. Never use the
dust extractor without a lter, or if the lter is damaged.
Do not use any unsafe work techniques.
Use extra care when cleaning on stairs.
Discard lter elements, lter bags and disposal bags in accordance
with the national regulations.
CAUTION: This machine shall be stored indoors only.
Provide for good ventilation at the working place.
English
26
If the machine is not working properly or has been dropped,
damaged, left outdoors, or dropped into water, return it to a service
center or dealer.

MAINTENANCE, CLEANING AND REPAIR

Remove the battery pack before starting any work on the
appliance.
Only carry out maintenance work described in the operating
instructions.
The ventilation slots of the machine must be kept clear at all times.
The detachable parts (include dust collector) should be removed
for cleaning.
Clean dust and debris from tool. Keep tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean
the tool since certain cleaning agents and solvents are harmful
to plastics and other insulated parts. Never use ammable or
combustible solvents around tools.
Depending on the number of running hours – the dust lter should
be renewed. Keep the machine clean with a dry cloth, and a small
amount of spray polish.
Never spray water on to the upper section of the vacuum cleaner.
Danger for persons, risk or short-circuiting.
For user servicing, the machine must be dismantled, cleaned and
serviced, as far as is reasonably practicable, without causing risk
to the maintenance sta and others. Suitable precautions include
decontamination before dismantling, provision for local ltered
exhaust ventilation where the machine is dismantled, cleaning of
the maintenance area and suitable personal protection.
During maintenance and repair work all contaminated parts that
could not be cleaned satisfactorily must be:
• Packed in well sealed bags
• Disposed of in a manner that complies with valid regulations for
such waste removal.
The appliance should be regularly inspected by a quali ed service
technician. For example, check the lters for damage and check the
airtightness of the appliance and the proper functionality of the
control mechanism.
The use of non-genuine spare parts, brushes and accessories
can impair the safety and or function of the appliance. Use only
Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
STORAGE
The appliance must be stored in a dry place and protected from
frost.
CAUTION: This machine shall be stored indoors only.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis