Princeton Tec VIZZ MPLS Bedienungs- Und Wartungsanleitung

VIZZ MPLS
®
Operating and Maintenance Instructions
ENGLISH:
Battery Installation - See Figure 1
3 AAA
• Alkaline (LR03)
• Lithium (L92)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and recommends recycling
batteries. For more information about battery recycling, please go to
https://batterysolutions.com
Observe proper battery polarity. Improper installation of the batteries will
damage the light and void the warranty.
!
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Lithium batteries offer extended constant brightness time,
extreme cold weather performance, and lighter weight. Rechargeable
NiCad or NiMH batteries may result in reduced brightness due to lower
nominal voltage.
The Vizz battery compartment has a waterproof seal. It is important to
keep this seal free from dirt and away from harsh chemicals in order to
preserve waterproof integrity. Inspect the seal every time batteries are
changed. If dirt is present, wipe gently with a damp cotton swab and
mild soap until dirt is removed.
Switch Operation - See Figure 2
From off:
Red
Single press -
White Spot
Double press -
Tripple Press - White flood
Five second hold - Lockout
From On in any mode:
Hold - Dimming
Press after more than two seconds - Off
A single press more than two seconds after the previous button press
will turn light off.
From off, 5 second hold will lock light to prevent accidental turn on
and resulting battery drain. The Indicator LED (located inside the power
button) will blink three times to confirm lock. 5 Second hold from the
locked state will unlock the light and the indicator LED will flash to
confirm unlock. Removal and replacement of batteries will also reset
Vizz to unlocked state
Troubleshooting
If the Vizz fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check circuit board for water (the seal may have be compromised by
improper rear cover installation or dirty seal). The light will resume nor-
mal operation once the water is shaken or blown out and the light is
left open until completely dry. If the light has been contaminated with
salt water, flush the unit with fresh water and dry as described above.
Vizz Tactical MPLS Accessories
To attach the Vizz Tactical MPLS to the NVG Shroud:
1. Slide the bracket arm into the NVG Shroud adapter plate, making
sure the pull tab is above the lip of the adapter plate and that the
male grooves on the bottom of the bracket arm are aligned inside
the female grooves on the bottom of the adapter plate.
2. Push the bracket arm securely into place, ensuring that the pull tab
audibly clicks over the lip of the NVG Shroud
adapter plate.
3. Your MPLS Headlamp should now be secured in the NVG Shroud.
You can rotate the headlamp to focus your light source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
2. Push up slightly on the bottom of the light housing.
Figure 1 – Battery Replacement
1 2
Figure 2 – Switch Operation
Figure 3 – Performance
Modes Runtime
4
SPOT HIGH
54h
SPOT LOW
90h
WHITE FLOOD
135h
RED
DISTANCE (m) 0
(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the point the device is first turned on—
using fresh batteries, until the light output reaches 10% of the initial value.
Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux
Figure 4 – Mounting System -
1 2
3. While pushing upward, use the tool on the provided headstrap to
press the tab of the arm bracket towards the headlamp housing, so
that it disengages from the NVG Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud adapter plate.
To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making sure the pull
tab is above the lip of the mount and that the male grooves on the
bottom of the bracket arm are aligned inside the female grooves on
the bottom of the mount.
2. Push the bracket arm securely into place, ensuring that the pull tab
audibly clicks over the lip of the Butterfly Mount.
3. Your MPLS Headlamp should now be secured in the Butterfly Mount.
The mount can be attached to the provided headstrap, MOLLE
straps, or any 1" webbing. You can rotate the headlamp to focus
your light source accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided headstrap to
press the tab of the arm bracket towards the headlamp housing, so
that it disengages from the Butterfly Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
USA Lifetime Warranty - International 10-YearWarranty
Due to International regulations, Princeton Tec's lifetime warranty can
only be offered to customers in the USA. Princeton Tec offers a 10-year
warranty to our customers outside the USA. FULL WARRANTY - Princeton
Tec warrants this product to be free from defects in workmanship and
materials under normal use for as long as you own this product. This
warranty covers all of the component parts of the product except
batteries. This warranty does not cover deterioration due to normal
wear or damage due to misuse, alteration, negligence, accidents, or
unauthorized repair. Princeton Tec will repair or replace parts which
are defective In workmanship or materials. Your authorized Princeton
Tec Dealer and Princeton Tec are the only facilities authorized to repair
the product. After (3) unsuccessful attempts to repair the product, you
have the right to elect replacement of the product or a refund of the
purchase price less allowance for use of the product. NO INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY.
(Some states do not allow the exclusion or limitation of incidental or
3
Press 1x:
Red
Press 2x:
White Spot
Press 3x:
White Flood
Press 1x from On:
Off
Beam Pattern
16 25
1
consequential damages, so the above limitations or exclusions may not
apply to you.) This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Princeton Tec reserves the right to change product specifications
without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a chemical known to
the State of California to cause birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first contact
Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please have your
light model, date of purchase and a brief description of the fault
you are experiencing. No warranty repairs will be accepted without
an RMA number.
3. Return the light without batteries to:
Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and
freight collect items will not be accepted.
4. Upon receipt your light will be processed in about two weeks.
Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2021 Princeton Tec
4
From any mode:
Hold:
Dimming
Press 5 seconds:
Lock-Out
Press 5 seconds from Lock:
Unlock
Regulated Reserve
- 132h
- 54h
6h 14h
16h 15h
79
2